background image

 

 

 

 

Part # AT7107A – Privacy Handset with Cradle 
1.  To use the Privacy Handset, plug the connector on the end of the  

coil cord  into the corresponding receptacle on the Junction Box.  See Diagram 3 

2. An active call can be terminated and an incoming call can be rejected by pressing 

the PTT button on the Privacy handset for more than 2 seconds.     
3. To switch from an active call with the Privacy handset to hands-free operation, 

place the Privacy handset into its cradle. Audio will then be routed to the speaker.  If 

the PTT is pressed for more than 2 seconds, it will terminate the call. 

4. If the Privacy handset is not placed into its cradle, after the call is terminated, a 
reminder tone will be heard through the speaker, one  minute after all activity is 

finished until the Privacy handset is returned to its handset. 

 

Part # AT8410A – Palm Mic 
 1. To use a Palm Mic. plug the connector on the end of the coil cord of the Palm 

Mic. into the corresponding RJ45 receptacle on Junction Box.   

2. Once connected, the pressing of the switch on the Palm Mic. will deactivate the 

Visor Mic. and activate the Palm Mic. 
 

Call Waiting in both Hands-free mode and with Privacy handset  

1. To answer an incoming call during an active call, press the PTT button for a short 

period. This will put the current call on hold and answer the incoming call.  
2. A short press on the PTT will toggle between the calls. 

3. Pressing the PTT for more than 2 seconds will terminate the call. 

 

Charging the battery 
1. With the handset turned off, the car kit will charge the battery to 60% in 

approximately 1 hour. The charge time will be longer if the handset is operational 

during charge time. 

2. For operator convenience, the handset’s backlight will remain on for ease of 
viewing during low/no-light conditions. 

 

NOTE!  Batteries will charge within the temperature window of -10 C to +40 C (50 F 

to 104 F). If the battery is outside the temperature window, no charge current will be 
supplied to the battery. 

 

Operating Specifications 

Input voltage range: 

11V dc to 32V dc 

Operating ambient: 

-30C to +60 C 

 

 

 

 
 

1150 NW 163

rd

 Drive, Miami, FL \33169 

T: 305-623-3939   F: 305-623-3996 

Summary of Contents for Verizon V860 - BARRAGE









Reviews: