background image

 

Warnings 

The following warnings are for the setup, use, grounding, maintenance, and repair of 
this equipment. The exclamation point symbol alerts you to a general warning and the 
hazard symbols refer to procedure-specific risks. When these symbols appear in the 
body of this manual or on warning labels, refer back to these Warnings. Product-specific 
hazard symbols and warnings not covered in this section may appear throughout the 
body of this manual where applicable. 

    WARNING 

 

ELECTRIC SHOCK HAZARD  

This equipment must be grounded. Improper grounding, setup, or usage of the system can cause 
electric shock. 

 

Turn off and disconnect power cord before servicing equipment. 

 

Connect only to grounded electrical outlets. 

 

Use only 3-wire extension cords. 

 

Ensure ground prongs are intact on power and extension cords. 

 

TOXIC FLUID OR FUMES HAZARD 

Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or 
swallowed.

 

 

Read Safety Data Sheets (SDSs) to know the specific hazards of the fluids you are using. 

 

Store hazardous fluid in approved containers and dispose of it according to applicable guidelines. 

 

BURN HAZARD 

Equipment surfaces and fluid that is heated can become very hot during operation. To avoid severe 
burns: Do not touch hot fluid or equipment.

 

 

PERSONAL PROTECTIVE EQUIPMENT 

Wear appropriate protective equipment when in  the work area to help prevent serious injury, 
including eye injury, hearing loss, inhalation of toxic fumes, and burns. Protective equipment includes 
but is not limited to:

 

 

Protective eyewear, and hearing protection.  

 

Respirators, protective clothing, and gloves as recommended by the fluid and solvent 
manufacturer. 

 

EQUIPMENT MISUSE HAZARD 

Misuse can cause death or serious injury.  

 

Do not operate the unit when fatigued or under the influence of drugs or alcohol.  

 

Do not exceed the maximum working pressure or temperature rating of the lowest rated system 
component. See Technical Specifications in all equipment manuals.  

 

Use fluids and solvents that are compatible with equipment wetted parts. See Technical 
Specifications in all equipment manuals. Read fluid and solvent manufacturer’s warnings. For 
complete information about your material, request SDSs from distributor or retailer.  

 

Turn off all equipment and relieve air pressure when equipment is not in use.  

 

Check equipment daily. Repair or replace worn or damaged parts immediately with genuine 
manufacturer’s replacement parts only.  

 

Do not alter or modify equipment. Alterations or modifications may void agency approvals and 
create safety hazards.  

 

Make sure all equipment is rated and approved for the environment in which it is used.  

 

Use equipment only for its intended purpose. Contact your distributor for information.  

 

Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.  

 

Do not kink or over bend hoses or use hoses to pull equipment.  

 

Keep children and animals away from work area.  

 

Comply with all applicable safety regulations.  

3A6328A 

Advanjet HM-2600 Hotmelt Jet Maintenance and Repair 

Page 5 of 28 

Summary of Contents for HM-2600





























Reviews: