background image

AIMB-C300 User Manual

14

Appendix A  Safety Instructions 

A.1  Safety Instructions 

1. Read these safety instructions carefully. 
2. Keep this User Manual for later reference. 
3. Disconnect this equipment from any AC outlet before cleaning. Do not 
use a damp cloth, liquid or spray detergents for cleaning. 
4. For plug-in equipment, the power outlet socket must be located near 
the equipment and must be easily accessible. 
5. Keep this equipment away from humidity. 
6. Put this equipment on a reliable surface during installation. Dropping it 
or letting it fall may cause damage. 
7. The openings on the enclosure are for air convection. Protect the equip-
ment from overheating. DO NOT COVER THE OPENINGS. 
8. Make sure the voltage of the power source is correct before connecting 
the equipment to the power outlet. 
9. Position the power cord so that people cannot step on it. Do not place 
anything over the power cord. 
10. All cautions and warnings on the equipment should be noted. 
11. If the equipment is not used for a long time, disconnect it from the 
power source to avoid damage by transient over-voltage. 
12. Never pour any liquid into an opening. This may cause fire or electri-
cal shock. 
13. Never open the equipment. For safety reasons, the equipment should 
be opened only by qualified service personnel. 
14. If one of the following situations arises, get the equipment checked by 
service personnel:
a. The power cord or plug is damaged. 
b. Liquid has penetrated into the equipment. 
c. The equipment has been exposed to moisture. 
d. The equipment does not work well, or you cannot get it to work 
according to the user manual. 
e. The equipment has been dropped and damaged. 
f. The equipment has obvious signs of breakage. 

    

Summary of Contents for AIMB-C300























Reviews: