2 MIC-3890 Startup Manual
OUTPUTS
Assignment DC VOLTAGE
CURRENT
PIN NBR
V01
+12V
min Typ Max CNT1-P8,P9
0A 20A 20A
COM
Return of all ouput
CNT1-
P6,P7,C3,B6,D4
5Vsb
+5V
0A 2.5A 2.5A CNT1-C6,D6
-VS
The negative remote sense
of V01
CNT1-A2
12VCS
The current share bus of V01
CNT1-B2
EN
Active low to enable
CNT1-A6
FAL
Active low to show power is fail CNT1-D2
+VS
The positive remote sense
of V01
CNT1-A3
PSNON
Active low to enable V01
CNT1-B3
PS_P
PS_present, pull low in the
PSU
CNT1-D3
A2
I²C address bit 2
CNT1-A4
A1
I²C address bit 1
CNT1-B4
A0
I²C address bit 0
CNT1-C4
SDA
Data interface respectively for
I²C logic
CNT1-A5
SCL
Clock interface respectively for
I²C logic
CNT1-B5
ALERT
Active low to alert fot PUMBus
CNT1-C2
DEG
Active low to show over tem-
perature
CNT1-D2
M12 Connector Input Pin Definition
Item
Pin define
Remark
1,4
+110V
Input anode
2,3
-110V
Input cathode
Wago Connector Input Pin Definition
Item
Pin define
Remark
1
+110V
Input anode
2
-110V
Input cathode
3
PE
GND
Input
•
Input Voltage:
Range 66V-160V
DC
; Type 110V
•
Input Current:
≤5A
•
Inrush Current:
Peak 11.4A at 160V
DC
•
Input Connector:
Wago 769-663/004-000/Harting 21 03
321 3401
Output
•
Output Voltage:
V1: +12V/STANDBY V2: +5V
•
Output Current (typ.):
V1: 20A/STANDBY V2: 2.5A
•
Output Wattage:
Typ. 250W continuous
•
Output Connector:
FCI 51939-667LF
•
Noise & Ripple:
5V: ≤100MV;12V: ≤120mV
•
Remote Sense:
Available at 12V
•
Current Sharing:
Available at 12V
Protection
•
Over Voltage:
Built-in (LATCH)
•
Over Current:
Installed
•
Over Temperature:
Available
General
• Efficiency:
≥84%
•
Switching Frequenc:
225~275KHz, Typical 250KHz
•
Dielectric Withstand:
1500V
AC
•
Remote ON/OFF:
Available
•
PM Bus Interface:
Available
•
Power Fail Signal:
Available at [FAL#] pin
•
DC OK:
Available for V1 & +5Vsb (V2)
•
N+1 Redundancy:
Internal OR-ing diodes
•
Hot-swappable:
Available
•
Status LED:
- <Green> means valid input voltage
- <Red> means a critical fault
1
V1: +12V
2
V2: +5V
Environmental
•
Operating Temperature:
-40 ~ 70° C (with air flow and
derating)
•
Storage Temperature:
-55° C to +85° C
•
Operating Humidity:
95 % @ 40° C, non-condensing
•
Cooling:
≥150W, forced air (2.42m³/min Fan)
•
Vibration:
2.0 Grms (5~500 Hz)
Safety/EMC
•
Emissions (conducted):
GB/T 24338.5/EN50121-4
•
Safety Standard:
GB/T 25119
•
Surge:
EN50121-3-2
•
Shock and Vibration:
GB/T 21563; GB/T 24338.4
•
Radiated Susceptibility:
EN50121-3-2/IEC 62236-3-2
Assignment
Volt.
Typ
Min
Max
V1
12V
20A
0A
20A
V2
5V
2.5A
0A
2.5A
Output Voltage & Current Rating Chart
Specifications
Pin Assignment
Derating Curve
