background image

v

PPC-L61T User Manual

 

Safety Instructions

1.

Read these safety instructions carefully.

2.

Keep this User Manual for later reference.

3.

Disconnect this equipment from any AC outlet before cleaning. Use a damp 
cloth. Do not use liquid or spray detergents for cleaning.

4.

For plug-in equipment, the power outlet socket must be located near the equip-
ment and must be easily accessible.

5.

Keep this equipment away from humidity.

6.

Put this equipment on a reliable surface during installation. Dropping it or letting 
it fall may cause damage.

7.

The openings on the enclosure are for air convection. Protect the equipment 
from overheating. DO NOT COVER THE OPENINGS.

8.

Make sure the voltage of the power source is correct before connecting the 
equipment to the power outlet.

9.

Position the power cord so that people cannot step on it. Do not place anything 
over the power cord.

10.

All cautions and warnings on the equipment should be noted.

11.

If the equipment is not used for a long time, disconnect it from the power source 
to avoid damage by transient overvoltage.

12.

Never pour any liquid into an opening. This may cause fire or electrical shock.

13.

Never open the equipment. For safety reasons, the equipment should be 
opened only by qualified service personnel.

14.

If one of the following situations arises, get the equipment checked by service 
personnel:

a. 

The power cord or plug is damaged.

b. 

Liquid has penetrated into the equipment.

c. 

The equipment has been exposed to moisture.

d. 

The equipment does not work well, or you cannot get it to work according to 

the userís manual.

e. 

The equipment has been dropped and damaged.

15.

DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE 
STORAGE TEMPERATURE MAY GO BELOW -20° C (-4° F) OR ABOVE 60° C 
(140° F). THIS COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT 
SHOULD BE IN A CONTROLLED ENVIRONMENT.

The sound pressure level at the operator's position according to IEC 704-1:1982 is
no more than 70 dB (A).

DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech
disclaims all responsibility for the accuracy of any statements contained herein.

Caution! DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY 

REPLACED.REPLACE ONLY WITH THE SAME OR EQUIVALENT 
TYPE RECOMMENDED BY THE MANUFACTURER, DISCARD USED 
BATTERIES ACCORDING TO THE MANUFACTURERíS INSTRUC-
TIONS.

Summary of Contents for PPC-L61T

































Reviews: