background image

 

SympTOm:

  No power at video monitor

  Power but no video or sound

  Disc will not play or wrong region is displayed

  IR Wireless Headphones do not work

  Game source does not work

19

TrOuBLEShOOTING

  

rEmEdy:

• 

 12 VDC on the Red wire at 6 Pin Power/Dome Light Harness behind 
the video monitor.  Verify a ground connection with a continuity test from a 
known good ground to the black wire.

• 

 Verify that the correct source is selected (DVD, USB, HDMI1, HDMI2, Media, AV, 
AUX, Game).  Verify that the source is on and playing a known good media.

• 

 Check the type of disc you put into disc slot and is inserted in the correct 
position. 

NOTE:

 The DVD system only plays digital video discs, audio CDs and 

MP3s.

• 

 Both the unit and the disc are coded by region. If the regional codes don’t 
match, the disc can’t be played. This DVD player is set to Region 1.

• 

 Check if batteries are installed correctly.

• 

Make sure that the headphone batteries are fresh.

• 

Check if Power Button lights up when pressed.  If Power Button does not light 
up when pressed, change batteries.

• 

If using Dual Channel Wireless Headphones, make sure the correct channel 
is selected.

• 

Make sure the IRT power is ON.  Press the IRT ON/OFF button on the remote 
control and IRT ON or IRT OFF is displayed.

• 

The Game Source can not be selected if the MVGP1 Game Module is not 
installed.  Make sure the MVGP1 Game Module is installed and plugged in.

Summary of Contents for ADVEXL12A

























Reviews: