Adventuridge 93410116 User Manual Download

Page: 5 / 16

STEP 1:

Spread tent out flat, floor side down.

STEP 2:

Extend fiberglass tent poles by pulling out each section

and placing it into the metal ferrule connectors. You will have five

poles. The two longest poles (A) are the main tent poles. The next

pair of poles (B) will be used on the sides of the tent. The single

pole with pre-bent ferrules (C) will be used for the front awning on

the tent fly.

STEP 3:

While making

sure sleeves are in line

with each other, slide the

main fiberglass tent poles

(A) through the sleeves

that are opposite each

other on the roof of the

tent. Straighten the

sleeves along the fiberglass sections. Position poles so that they

form an “X” across the tent.

STEP 4:

Starting at the back of the tent,

place the ferrule at the end of the poles

onto the pins located on the rings at the

edge of the tent.

STEP 5:

(Please read and follow

IMPORTANT SAFETY

WARNING

that appears before Step 1.) While one adult holds the

end of the tent pole firmly in place on the pin at the rear of the tent,

the other adult should now go into the front door of the tent

and gently lift the roof at the crossed tent poles off the

ground. When the tent and poles are raised, the first adult who is

at the rear of the tent, goes to the front of the tent, flexes the

fiberglass pole and places the metal ferrule at the end of the main

tent pole onto the pin located on the ring at the base of the tent.

Repeat step for the other main tent pole. Clip

plastic hooks to the fiberglass frame poles.

Locate the fabric ties

attached to the

center of the tent

roof and tie both

poles together.

STEP 6:

Stake down tent by

inserting the steel stakes through

the metal rings and stake loops

attached at the base of the

tent. Hammer stakes into

ground at a 45° angle by

using a hammer or mallet.

Make sure to pull tent out even

and tight.

IMPORTANT:

WE ADVISE YOU TO ASSEMBLE THE

TENT ONCE BEFORE GOING CAMPING TO BECOME

FAMILIAR WITH THE ASSEMBLY OF THE TENT.

NOTE: PLEASE LOOK AT THE REPLACEMENT

PARTS DIAGRAM TO SEE HOW YOUR FRAME IS

ASSEMBLED.
TO PROLONG THE LIFE OF THE TENT FLOOR,

SELECT A LEVEL, CLEAN AREA FOR THE CAMPSITE.

TO PREVENT DAMAGE TO THE ZIPPER, UNZIP THE

DOORS TO ALLOW AIR TO ENTER THE TENT.
TO IMPROVE THE WEATHER RESISTANCE OF YOUR

TENT, IT IS ADVISABLE TO USE SEAM SEALER TO

COAT ALL EXPOSED SEAMS. YOU SHOULD APPLY

ONLY TO THE INSIDE SEAMS OF THE TENT AND

UNDERSIDE OF THE TENT FLY. IF APPLIED TO THE

OUTSIDE OF SEAMS, DISCOLORATION OF YOUR

TENT MAY OCCUR. SEAM SEALER IS AVAILABLE IN

THE CAMPING SECTION OF ANY LOCAL SPORTING

GOODS STORE.

WARNING:

During assembly of the main room and

side room tent pole, the tent poles are in tension. If the

poles are not held firmly in place by adults during assembly,

the tension in the poles may cause them to break or one end

of the pole to flip up, which could cause serious injury to you

or others involved in assembling the tent. To avoid this

hazard:

• DO HAVE two adults involved in assembling the tent.
• DO HAVE one adult hold the end of the tent pole in

place in the grommets at the crossed tent poles. When

the tent and poles are raised, the first adult who is at

the rear of the tent, goes to the front of the tent and

completes the pole connection into the grommets at the

front of the tent.

Failure to follow this warning could cause serious injury to

you or others involved in assembling this tent.

Tent should appear

as shown.

STEP 7:

(Please read and follow the

IMPORTANT SAFETY

WARNING

that appears before Step 1.) To assemble the side

rooms, locate the longer remaining pair of fiberglass poles (B).

Insert one of the pole sections through pole sleeve at the top of the

side room. With an adult on each end of the side room pole,

gently flex the pole into an arch and place the metal tips at the end

of the side room poles onto the pin located on the ring at the base

of the tent. Clip plastic hooks to the fiberglass frame poles.

Repeat the same procedure for the remaining side room.

STEP 8:

Place fly over tent so the

front awning is located over the

front of the tent. Attach the fly to

the tent by hooking the

S-hooks located at the fly

corners to the metal rings at the

base of the tent.

WARNING:

Elastic cords can snap back and hit your eye.

To reduce the risk of injury to you and others:

• Keep your body and face clear.
• Do not over stretch elastic cords.
• Maintain firm grip on hook.
• Pull the hook toward you; if it slips it will spring away from you.
• Make sure hook is fully clipped to tent before releasing.
• Wear protective eyewear during tent assembly.

Your failure to follow this warning could cause serious injury or

permanent disability.

STEP 9:

Insert the fly awning (C) pole into the sleeve at the front

of the fly. Insert the pole ends onto the pins at the base of the tent.

STEP 10:

Stake down the vestibule by inserting the stakes

through the stake loops and hammer the stakes into ground at a

45° angle.

STEP 11:

Fasten the Velcro

fasteners on the underside of the fly