background image

5

14. Switch out of memory LOAD and press [4]. The message should now read "NR 162 DE K1XX

K". You have just edited your old message!

15. Now press [4] again and play back the message until NR 163 DE and press the dot key paddle

to hold the message ahead of K1XX. Switch the memory switch to LOAD and press [

*

][5] to ed-

it.  With  the  paddle  send  "K1XX"  and  (without  pressing  [#])  switch  the  memory  switch  out  of
LOAD mode.

16. Press  [4]  and  and  the  message  should  now  read  "NR  164  DE  K1XX  K1XX".  You  have  just

edited a message by inserting a word in the middle!

17. Now switch the memory switch to LOAD and press [4] and send "TEST" with your paddle. With-

out  pressing  [1]  return  the  memory  switch  from  the  LOAD  mode  and  press  [4].  The  message
should now read "TEST NR 165 DE K1XX K1XX K". You have now edited the message by add-
ing on to the front of the message.

Automatic Message Repeat

1. Switch the memory switch to LOAD and press [1]. Send "CQ CQ DE K1XX K1XX K", press [#]

and switch out of LOAD.

2. Turn the repeat switch/pot clockwise until the repeat LED lights. Turn the pot all the way clock-

wise until the message you loaded into location 1 is automatically activated. A delay time of up
approximately two minutes is possible with the CK-2.

3. In the middle of the message playback in the repeat mode, try tapping the paddle to interrupt

the message. Note that no additional character is transmitted until after you let up on the pad-
dle /the first time) and then commence sending. When no characters have been manually sent
for  a  period  of  time  equal  to  the  delay  setting,  the  CK-2  will  automatically  start  sending  mes-
sage 1 again.

Summary of Contents for CK-2





















Reviews: