background image

4

17

Insertion and fixing

Before inserting the hob in the installation
opening, place the special gasket around
the bottom edge of the hob.

It is important to fix this gasket evenly, without
gaps or overlapping, to prevent liquid from
seeping underneath the hob.

1) Remove the pan stands and the burner

caps and turn the hob upside down, taking
care not to damage the ignition plugs and
the thermocouples.

2) Place the gasket around the bottom edge

of the hob as shown in the illustration on
the right.

3) Place the hob in the installation opening

and push it down so that the hob is resting
firmly on the cabinet, as shown in the
illustration.The side springs will hold it in
place.

A) gasket

Building into fitted kitchen units

These hobs are designed for installation in fitted kitchen units up to 600 mm deep
with suitable characteristics.
Any cabinet side panels taller than the height of the hob itself must be at least 150
mm away from the opening into which the hob is inserted.
The dimensions of the hob and the installation opening are shown in the illustration.

480

560

70

680

510

50

600

a

Child safety

• This hob is designed to be operated by adults. Do not allow children to play near

or with the hob.

• The hob gets hot when it is in use. Children should be kept away until it has cooled.

• Children can also injure themselves by pulling pans or pots off the hob.

Cleaning and maintenance

• Keep the appliance thoroughly cleaned. Food residues may cause fire risks.

Service and Spare Parts

• In the instance of malfunctions, never attempt to repair the appliance yourself.
Repairs by unskilled persons may cause damage and accidents. First refer to the
contents of this manual. If you do not find the necessary information, contact your
nearest Service Centre. Servicing work on this appliance must be carried out by an
authorized Technical Service Centre. Always request the use of original spare parts.

      Environmental Information

• All the materials used are environmentally compatible and recyclable.

Contact your Local Council or Environmental Health Office  to see if there are facilities
in your area to recycle the appliance.

Decommissioned appliances

• Appliances which are no longer used or usable are not worthless waste. Through

environment-friendly disposal, a number of materials used in the production of your
appliance can be recovered.

• Before scrapping the appliances, cut the power supply lead and make it

unusable.

•  Keep this instruction book for future reference and ensure it is passed on to

any new owner.

These instructions only apply for the countries of destination whose
identification symbols appear on the cover of the instruction manual and
on the appliance .

Summary of Contents for 25742 GM





















Reviews: