AEG A18FCN18GA, Original Instructions Manual

14

TECHNICAL DATA

A18FCN18GA / A18FCN18GANZ

Type

Brad nailer

Battery voltage

18 V 

Fastener type

18GA Brad nails

Diameter

1.2 mm

Length min./max

15.9 - 54 mm

Recommended Cycle rate

900 / hour

%XUVWF\FOHUDWH$)&1*$±EXPS¿UHPRGH

1 / second

Burst cycle rate (A18FCN18GANZ)

1 / second

Magazine capacity

105 nails

Fastener range

15.9 to 54 mm

Weight without battery pack

2.45 kg

Noise Information

Measured values determined according to EN 60745. Typically, the A-weighted noise 

levels of the tool are:
Sound pressure level / Uncertainty

Sound power level / Uncertainty

Wear ear protection!

L

pA

=85.5 dB (A) / K

pA

=3 dB(A)

L

WA

=96.5 dB (A) / K

WA

=3 dB(A)

Vibration Information

Vibration total values (triaxial vector sum) determined according to EN 60745.

Vibration emission value / Uncertainty

a

h

=

2.5 m/s

2 

/ K=1.5 m/s

2

WARNING!

The declared vibration total values and the declared noise emission values given in this instruction manual have been measured in 

accordance with a standardised test and may be used to compare one tool with another. They may be used for a preliminary assessment of 

exposure.
The declared vibration and noise emission values represent the main applications of the tool. However, if the tool is used for different 

applications, used with different accessories, or poorly maintained, the vibration and noise emission may differ. These conditions may 

VLJQL¿FDQWO\LQFUHDVHWKHH[SRVXUHOHYHOVRYHUWKHWRWDOZRUNLQJSHULRG

An estimation of the level of exposure to vibration and noise should take into account the times when the tool is turned off or when it is 

UXQQLQJLGOH7KHVHFRQGLWLRQVPD\VLJQL¿FDQWO\UHGXFHWKHH[SRVXUHOHYHORYHUWKHWRWDOZRUNLQJSHULRG

Identify additional safety measures to protect the operator from the effects of vibration and noise, such as maintaining the tool and the 

accessories, keeping the hands warm (in case of vibration), and organising work patterns.

COMPATIBLE BATTERY PACKS (NOT INCLUDED)

L1820R
L1820S
A18FB2
L1825R
L1830R-X5

A18B4
L1840R
A18FB4
L1850R
A18FB5

L1860R
L1860R-X5
L1890R

Use AEG 18V battery and charger only

WARNING! Read all safety warnings, instructions, 

LOOXVWUDWLRQVDQGVSHFL¿FDWLRQVSURYLGHGZLWKWKLVSRZHUWRRO

Failure to follow all instructions listed below may result in electric 

VKRFN¿UHDQGRUVHULRXVLQMXU\6DYHDOOZDUQLQJVDQGLQVWUXFWLRQ

for future reference.

NAILER SAFETY WARNINGS

$OZD\VDVVXPHWKDWWKHWRROFRQWDLQVIDVWHQHUV

Careless 

KDQGOLQJRIWKHQDLOHUFDQUHVXOWLQXQH[SHFWHG¿ULQJRIIDVWHQHUVDQG

personal injury.

'RQRWSRLQWWKHWRROWRZDUGV\RXUVHOIRUDQ\RQHQHDUE\

Unexpected triggering will discharge the fastener causing an injury.

'RQRWDFWXDWHWKHWRROXQOHVVWKHWRROLVSODFHG¿UPO\DJDLQVW

WKHZRUNSLHFH

 If the tool is not in contact with the workpiece, the 

IDVWHQHUPD\EHGHÀHFWHGDZD\IURP\RXUWDUJHW

'LVFRQQHFWWKHWRROIURPWKHSRZHUVRXUFHZKHQWKHIDVWHQHU

MDPVLQWKHWRRO

 While removing a jammed fastener, the nailer may 

be accidentally activated if it is plugged in.

8VHFDXWLRQZKLOHUHPRYLQJDMDPPHGIDVWHQHU

 The mechanism 

may be under compression and the fastener may be forcefully 

discharged while attempting to free a jammed condition.

'RQRWXVHWKLVQDLOHUIRUIDVWHQLQJHOHFWULFDOFDEOHV

It is 

not designed for electric cable installation and may damage the 

LQVXODWLRQRIHOHFWULFFDEOHVWKHUHE\FDXVLQJHOHFWULFVKRFNRU¿UH

hazards.

ADDITIONAL SAFETY WARNINGS

The product is designed for single-hand use. Do not hold the 

product by the front of the magazine. Do not put hands, head, or 

other parts of your body near the bottom of the magazine where 

the fastener exits the product, as serious personal injury could be 

caused.
Always ensure that the workpiece contact is fully positioned above 

the workpiece. Positioning the workpiece contact only partially 

above the workpiece could cause the fastener to miss the workpiece 

completely and result in serious personal injury.
Do not drive fasteners near edge of material. The workpiece may 

split causing the fastener to ricochet, injuring you or a coworker. Be 

aware that the fastener may follow the grain of the wood, causing 

it to protrude unexpectedly from the side of the work material or 

GHÀHFWSRVVLEO\FDXVLQJLQMXU\

Keep hands and body parts clear of immediate work area. Hold 

workpiece with clamps when necessary to keep hands and body out 

of potential harm. Be sure the workpiece is properly secured before 

pressing the fastener against the material. The workpiece contact 

may cause the work material to shift unexpectedly.
Keep face and body parts away from back of the tool cap when 

working in restricted areas. Sudden recoil can result in impact to the 

body, especially when nailing into hard or dense material.
During normal use the product will recoil immediately after driving a 

fastener. This is a normal function of the product. Do not attempt to 

prevent the recoil by holding the nailer against the work. Restriction 

to the recoil can result in a second fastener being driven from the