English
34
EON TA
The unit can receive RDS EON data. EON means
the transmission of additional programme
information within a station group. In the event of
a traffic announcement (TA), it will switch within a
station group from a non-traffic broadcast to the
corresponding traffic radio station of the station
group.
DX
: The unit attempts to receive the EON TA
information from a receivable station and thus
to improve the reception quality.
LO
: This prevents switching to a programme
with too weak a signal level.
TA VOL
Traffic Announcement Volume
REG
Some stations split their programme at certain
times into regional programmes with different
content.
ON
: Only the regional programmes of the
station are played.
OFF
: National programmes are also played.
Loudness Function
Press and hold
/LOU/BND
(15) to activate the Loud-
ness function.
LOUD ON
is displayed. The Loudness
function enhances the bass frequencies.
Press and hold
/LOU/BND
(15) again to deactivate
the Loudness function.
LOUD OFF
is displayed.
NOTE:
The loudness function cannot be applied in the
BT
AUDIO
mode. If necessary, change the sound settings
on your mobile phone.
Sound Settings
Repeatedly press
TA/EQ
(22) to cycle through the set-
tings
FLAT, CLASSICS, POP M, ROCK M
or
DSP OFF
.
The selected setting is displayed.
Display Information
Repeatedly press
DSP
(24) to cycle through the following
display information:
Time (is automatically set if RDS reception is enabled), radio
station, programme type, frequency of the currently set radio
station, information on file names (only during playback of a
MP3 or WMA file).
NOTE:
If there is no corresponding information,
PTY NONE
is
shown on the display.
If the information is too long for the display, it is dis-
played as scrolling text.
Setting the time manually (in Radio Mode)
If the time should not be set automatically, proceed as fol-
lows:
Press the button
DSP
(24) for a short while until the time
appears on the display.
Keep the
DSP
button (24) pressed until the time flashes
on the display.
Use the button (7) to set the minutes.
Use the button (13) to set the hours.
Reset Radio
To reset the unit to default settings press
RESET
(29) with a
pointed object, i.e. pen.
Reset the unit when:
using it the first time after all cabling is done,
malfunctions of buttons occur,
error messages are displayed.
Radio Functions
Set RADIO Mode
Repeatedly press
MODE/PAIR
(17) until frequency and
band are displayed.
Select Frequency Band
Press
/LOU/BND
(15) to toggle between FM1, FM2,
FM3 and AM. The selected frequency band is displayed.
Auto Search
Press (7) or (13) to start auto search,
SEARCH
is
displayed. Search stops if a station is found.
Manual Search
Press and hold (7) or (13) until
MANUAL
is displayed.
Press (7) or (13) to step through the FM frequency
band in steps of 0.05 MHz and 9 kHz for AM until the
desired frequency is displayed.
After two seconds idling the unit returns to auto search. The
display shows
AUTO
.
Save Station
For each frequency band 6 station presets are available.
Press and hold the desired numeric button (2-4, 18, 23,
26) approx. 2 seconds to save the current station. A beep
can be heard after successful storage (except setting to
BEEP OFF
).
Access Saved Station
Press
/LOU/BND
(15) to select the desired frequency
band.
Press one of the numeric buttons (2-4, 18, 23, 26) to ac-
cess the respective station.
Auto Save
Press
/LOU/BND
(15) to select the desired frequency
band.
Summary of Contents for AR 4029 DAB
