9
9
WARNING! Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in electric
shock, fire and/or serious injury.
Save all warnings and instructions
for future reference.
SUPERCLAMP SAFETY WARNINGS
Know your product. Read the operator’s manual for the product and
for any tool being used with this workstation.
Do not allow familiarity with tools to make you careless. Remember
that a careless fraction of a second is sufficient to inflict severe injury.
Always wear eye protection with side shields marked to comply with
AS/NZS 1337. Failure to do so could result in objects being thrown into
your eyes, resulting in possible serious injury.
Do not use any attachments or accessories not recommended by the
manufacturer of the product. The use of attachments or accessories
not recommended can result in serious personal injury.
Keep fingers, hands, and all body parts away from moving clamps.
Failure to do so could result in possible serious injury.
Stop immediately if the workpiece or product moves when operating.
Failure to do so could result in possible serious injury.
Make sure all moving parts are free from interference.
Keep hands free of all moving parts to avoid pinching and other
injuries.
Place the product on a firm, level surface where there is plenty of
room to handle and properly support the workpiece.
Make sure workpieces are properly supported.
Never perform work on the product outside the width of the front
legs. Doing so may cause the product to become unbalanced and tip.
Check that all screws and knobs are tight and legs are securely locked
before operating the product.
Do not use as a stepladder, standing platform, or scaffolding support.
Stop immediately if the workpiece or the product moves when
operating.
Check to make sure the product does not rock, slide or move prior
to use.
Save these instructions. Refer to them frequently and use them to
instruct other users. If you loan someone the product, also loan these
instructions.
RESIDUAL RISKS
Even when the product is used as prescribed, it is still impossible
to completely eliminate certain residual risk factors. The following
hazards may arise and the operator should pay special attention to
avoid the following:
Ŷ
Keep other persons away.
–
Do not let persons, especially children, not involved in the
work touch the tool and keep them away from the work area.
Ŷ
Ensure the product is set up on a firm, level ground in a stable
manner.
Ŷ
Check to make sure that all fixing screws and knobs are tight and
all legs are locked in place before using the tool.
Ŷ
Ensure the workpiece is clamped firmly and the lock release
switch is in proper state before use. Unclamped workpieces can
cause severe injury and damage.
SPECIFIED CONDITIONS OF USE
The superclamp is intended to clamp wood, metal, plastics or any
other physical object, to support with other hand tools. The product is
also intended to be used on a level surface and in a dry environment.
The product is intended to be maintained by a skilled/qualified
operator following the operator’s instruction manual, and is not
intended to be used by anyone under 18 years old.
ASSEMBLY
WARNING
Do not use this product if it is not completely assembled or if any
parts appear to be missing or damaged. Use of a product that
is not properly and completely assembled or with damaged or
missing parts could result in serious personal injury.
WARNING
Do not attempt to modify this product or create accessories or
attachments not recommended for use with this product. Any such
alteration or modification is misuse and could result in a hazardous
condition leading to possible serious personal injury.
UNPACKING
Packing list
Ŷ
Superclamp x 1
Ŷ
Operation manual x 1
OPERATION
SETTING UP THE PRODUCT
See Figures 1 - 8.
Ŷ
Place the product upside down on a flat level surface.
Ŷ
Unlock the leg lock lever.
Ŷ
Slide the rear leg towards the back of the product releasing it
from the storage hole.
Ŷ
Lift the leg slightly then slide the leg toward the front of the
product.
Ŷ
Raise the leg and slide it down into place before locking the leg
lock lever.
Ŷ
Unlock the rear foot lock lever.
Ŷ
Depress the upper lock button to release the adjustable foot.
Ŷ
Tilt the adjustable foot until it is perpendicular to the rear leg and
push down to engage the lower lock button.
Ŷ
Lock the foot lock lever.
Ŷ
Lift the foot pedal and pull toward the front of the product until
it clicks into place.
Ŷ
Lift the right front leg and pull to the front of the product until leg
locks in place. Repeat for left leg.
NOTE:
When the legs are secure, the lock levers will prevent
TECHNICAL DATA
SUPERCLAMP
ASJ-01
Clamping range
0 - 940 mm.
Clamping force
1 ton.
Maximum load
250 kg.
Weight
19 kg
