AEG BBTL18, Original Instructions Manual

10

10

4.  Press and release   to play the next track.
5.  Press and release 

 to cycle between pausing and 

playing the audio.

NOTE:

– These controls may not be supported by the 

BLUETOOTH

®

  device and application.

– All BLUETOOTH

®

 enabled device controls can be used 

normally while paired to the product.

– Volume for any device paired to the product can be 

adjusted using the volume control for that device or by 
pressing   or 

 on the product.

6.  Press and hold 

 for about two seconds to disconnect all 

BLUETOOTH

®

 enabled device. When the BLUETOOTH

®

LED indicator begins blinking, the product is ready to pair.

USING THE USB DEDICATED CHARGING PORT
See page 6.

The USB dedicated charging port provides charging power of 

up to 1 Amp for your cell phone, MP3 player, tablet, or other 

USB devices.

 CAUTION

Attempting to charge devices rated more than 1 Amp could 

damage the USB dedicated charging port and/or the device.

1.  Connect one end of a USB cable (not provided) to your 

USB device.

2.  Connect the other end of the USB cable (not provided) 

to the USB dedicated charging port to begin charging the 

device.

NOTE:

 The USB dedicated charging port provides power only; 

it does not provide any data communication capabilities.

When the product is operating on battery power, the 

USB dedicated charging port will continue to function for 

approximately 1 hour after switching the product off. If the 

product remains inactive after this time, charging will stop. Turn 

the product on to resume operation.

TONE ADJUSTMENT

Press 

 or 

 for bass and treble adjustment, 

in a range of 3dB for each setting.

MUTE REMINDER

When the product is switched on and volume is set at 0, the   

LED indicator will flash (3-4/sec).

BATTERIES

Battery packs which have not been used for some time should 

be recharged before use.
Temperatures in excess of 50°C reduce the performance of 

the battery pack. Avoid extended exposure to heat or sunshine 

(risk of overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, the battery packs have to be fully 

charged, after used.
To obtain the longest possible battery life remove the battery 

pack from the charger once it is fully charged.

For battery pack storage longer than 30 days:

•  Store the battery pack where the temperature is below 

27°C and away from moisture.

•  Store the battery packs in a 30% - 50% charged condition.
•  Every six months of storage, charge the pack as normal.

TRANSPORTING LITHIUM BATTERIES

Lithium-ion batteries are subject to the Dangerous Goods 

Legislation requirements.
Transportation of those batteries has to be done in accordance 

with local, national and international provisions and regulations.

■ The user can transport the batteries by road without further 

requirements.

■ Commercial transport of Lithium-Ion batteries by third 

parties is subject to Dangerous Goods regulations. 

Transport preparation and transport are exclusively to 

be carried out by appropriately trained persons and the 

process has to be accompanied by corresponding experts.

When transporting batteries:

■ Ensure that battery contact terminals are protected and 

insulated to prevent short circuit.

■ Ensure that battery pack is secured against movement 

within packaging.

■ Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice

BATTERY PACK PROTECTION

The battery pack has overload protection that protects it 

from being overloaded and helps to ensure long life. Under 

extreme stress the battery electronics switch off the machine 

automatically. To restart, switch the machine off and then 

on again. If the machine does not start up again, the battery 

pack may have discharged completely. In this case it must be 

recharged in the battery charger.

MAINTENANCE

The ventilation slots of the machine must be kept clear at all 

times. 
Use only AEG accessories and AEG spare parts. Should 

components need to be replaced which have not been 

described, please contact one of our AEG service agents (see 

our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please 

state the Article No. as well as the machine type printed on 

the label and order the drawing at your local service agents 

or directly at:

Techtronic Industries (Australia) Pty. Ltd. 

PO Box 1065 

Mount Waverley VIC 3149 

Tel. no. 1300 361 505 

Australia

Techtronic Industries N.Z. Ltd

.

PO Box 12-806 

Penrose AUCKLAND 1642 

Tel no. 0800 279 624 

New Zealand

SYMBOLS