9
9
WARNING
The product is not waterproof. Do not submerge in liquid.
Failure to heed this warning could result in serious personal
injury.
WARNING
Always refer to the manual for any device recommended
for use as an attachment or accessory. Proper use of
any device, when attached to the product, is the sole
responsibility of the operator. Improper use may damage
the device or the product.
INSTALLING/REMOVING BATTERY PACK
See page 3.
The product is operated by an AEG 18V battery pack.
1. Place the battery pack in the product, aligning the ribs on
the battery pack with the grooves in the battery port.
2. Make sure the latches on the battery pack snap into place
and the battery pack is secured to the product before
beginning operation.
3. Depress the latches to remove the battery pack.
NOTE:
Always remove the battery pack from the product when
not in use. Leaving the battery pack connected for long periods
of time may drain the battery pack.
CONTROL PANEL
See page 2.
Use the control panel to switch the product on and off, control
the volume and toggle between modes.
SWITCHING THE PRODUCT ON AND OFF
Press the on/off button for 1 second to switch the product on
and off. The LED indicator will be on.
The LED indicator will flash (1/sec) if battery is low.
MODE SELECTION
See page 2.
There are two modes to choose from:
■ AUX mode
■ BLUETOOTH
®
mode
■ Press
to cycle through AUX mode and
BLUETOOTH
®
mode.
■ The current mode is indicated by either the
or
LED.
ADJUSTING THE VOLUME
See page 2.
When the product is switched on, the product will return to the
last volume setting used.
■ To increase the volume, press
.
■ To decrease the volume, press .
NOTE:
To change volume quickly, hold
or .
CAUTION
Do not use the product at maximum volume for an extended
period of time with the bass and treble at maximum levels.
It could cause damage to the speakers and/or amplifiers in
the product.
AUXILIARY MODE
See page 4.
The product can be used as an amplifier for MP3 players, CD
players, smartphones, tablets, and other music devices.
To use the auxiliary mode:
1. Press
to AUX mode.
2. Connect auxiliary cable to the device.
3. Connect the other end of the auxiliary cable to the auxiliary
input port.
NOTE:
– The external device must be on and in play mode for
sound to be heard through the speakers.
– All external device controls can be used normally while
connected to the product.
– Volume for any device connected through the auxiliary
cable can be adjusted using the volume control for that
device or by using
or of the product.
– Switching the product off will not switch the external
device off.
– The auxiliary cable does not provide charging function.
4. For complete operating instructions for the connected
device, always refer to the manual that was included with
your device.
USING A BLUETOOTH
®
ENABLED DEVICE (NOT
INCLUDED) WITH THE PRODUCT
See page 5.
1. Press
until the BLUETOOTH
®
LED indicator is
flashing.
NOTE:
– When the product is switched to BLUETOOTH
®
mode,
the product will attempt to pair to a BLUETOOTH
®
enabled device.
– The product will automatically attempt to connect to the
last device it was paired to. If a connection cannot be
established within five seconds, the product will make
itself available to other BLUETOOTH
®
enabled devices.
– BLUETOOTH
®
enabled devices must be within 10 m
(30 ft) of the product and set to search/scan in order to
pair with the product.
2. Select “AEG Speaker” from your device’s list of available
BLUETOOTH
®
signals to pair the device and the product.
No password or PIN is required for connection.
NOTE:
– When a device is paired to the product, the
BLUETOOTH
®
LED indicator will stop flashing and
remain on. Information for connecting to the device is
saved in the product’s memory.
3. Press and release to replay current track. Press twice
to play the previous track.
Summary of Contents for BBTL18
