AEG BSS18BLC, Original Instructions Manual

14

14

BATTERY AND CHARGER

Compatible battery pack  

(not included)

Compatible charger  

(not included)

L1815R
L1820R
L1825R
L1830R
L1840R

L1850R
L1860R
L1860B

L1860R-X5

L1890R

AL18G

AL1218G

BL1218

BLK1218

BL18DP-X5

BL18DP2-X5

Use AEG 18V battery and charger only

WARNING! Read all safety warnings, instructions, 

illustrations  and  specifications  provided  with  this  power 

tool.

 Failure to follow all instructions listed below may result in 

electric  shock,  fire  and/or  serious  injury. 

Save  all  warnings  and 

instructions for future reference.

IMPACT DRIVER SAFETY WARNINGS

Hold  the  power  tool  by  insulated  gripping  surfaces,  when 

performing  an  operation  where  the  fastener  may  contact 

hidden  wiring.

 Fasteners contacting a “live” wire may make 

exposed metal parts of the power tool “live” and could give the 

operator an electric shock.

Wear ear protectors.

 Exposure to noise can cause hearing loss.

Sawdust and splinters must not be removed while the machine 

is running.
When  working  in  walls,  ceiling,  or  floor,  take  care  to  avoid 

electric cables and gas or waterpipes.
Remove  the  battery  pack  before  starting  any  work  on  the 

machine.
Do not dispose of used battery packs in the household refuse 

or by burning them.

 AEG Distributors offer to retrieve old batteries 

to protect our environment.

Do  not  store  the  battery  pack  together  with  metal  objects 

(short circuit risk).
Use  only  System  GBS  chargers  for  charging  System  GBS 

battery packs.

 Do not use battery packs from other systems.

Battery acid may leak from damaged batteries under extreme 

load or extreme temperatures. In case of contact with battery 

acid wash it off immediately with soap and water.

 In case of eye 

contact rinse thoroughly for at least 10 minutes and immediately 

seek medical attention.

SPECIFIED CONDITIONS OF USE

The impact driver may be used to tighten and loosen nuts and 

bolts for independent use away from mains supply.
Do not use the product for any other purpose.

BATTERIES

Battery packs which have not been used for some time should be 

recharged before use.
Temperatures in excess of 50°C (122°F) reduce the performance 

of the battery pack. Avoid extended exposure to heat or sunshine 

(risk of overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, the battery packs have to be fully charged, 

after used.
To obtain the longest possible battery life remove the battery pack 

TECHNICAL DATA

18V BRUSHLESS IMPACT DRIVER

BSS18BLC

Rated voltage  

 18 V

Tool reception  

 1/4” (6.35 mm)

No-load speed  

 0 - 2650 min

-1

Impact rate  

 3500 min

-1

Max torque  

 195 Nm

Max. diameter bolt / nut  

 M14

Recommended ambient operating temperature  

 -18...+50 °C

Weight - not including battery pack  

 1.2 kg

Measured values determined according to EN 60745. 
A-weighted sound pressure level  

L

p

 = 99.0 dB(A)

Uncertainty K  

 3 dB

A-weighted sound power level  

L

W

 = 110.0 dB(A)

Uncertainty K  

 3 dB

Wear ear protectors.
The vibration total values (triaxial vector sum) determined according to EN 60745:
Impact tightening of fasteners of the maximum capacity of the tool  

a

h

 = 19.1 m/s

2

Uncertainty K  

 1.5 m/s

2

WARNING

The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745 

and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure. The declared vibration 

emission level represents the main applications of the tool. However if the tool is used for different applications, with different accessories 

or poorly maintained, the vibration emission may differ. This may significantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is running 

but not actually doing the job. This may significantly reduce the exposure level over the total working period. 
Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the accessories, keep 

the hands warm, organisation of work patterns.