g
34
4.2
Selecting the Cup Measure
0
Repeatedly press the "Cup Measure"
key (Fig. 3, d) until the desired cup
symbol is indicated.
The cup measures are indicated as fol-
lows:
Espresso cup
Coffee cup
Coffee mug
The coffee machine is factory-set to
standard measures.
3
Notes on changing the cup measures
can be found in „Changing and Saving
the Cup Measure" Page 35.
4.3
Dispensing Coffee
Refer to „Dispensing Coffee" Page 33.
5
Frothing Milk
The steam can be used to froth milk
and to heat liquids. Since a higher
temperature is needed to produce
steam than to make coffee, the coffee
machine has an additional steam
mode.
3
To make a cappuccino, fill a large cup
1/2 to 2/3 full with espresso, and then
add the frothed milk.
1
Caution! Danger of scalding when the
steam nozzle is activated! Hot water or
steam output can cause scalding. Do
not activate the steam nozzle until it is
immersed in the milk.
0
To produce steam, press the "Steam
Pre-selector" key (Fig. 3, g)
. The
indicator illuminates, and at the same
time, the "Coffee machine heating"
indicator (Fig. 3, i)
flashes. When the
heating process is finished, this indica-
tor changes from flashing to con-
stantly on. The coffee machine is now
ready for frothing milk.
3
If the steam function is left unused for
more than 1 minute, the coffee
machine automatically changes back
to coffee-making mode.
0
Pour approximately 100 ml cold,
skimmed or semi-skimmed milk into a
small, narrow jug (max. 0.5 l capacity).
This must be small enough to fit under
the steam nozzle.
3
The milk should be cold. You should
also use a cold jug, and not rinse this
with hot water.
0
Swivel the steam nozzle out and hold
the jug under the steam nozzle so that
the end is completely immersed in the
milk. Turn the Selection dial for steam
and hot water (Fig. 1, D) to the
position
(Fig. 17)
. The milk is now
frothed up.
3
Hold the jug steady duing the frothing
process. The nozzle should not be
allowed to touch the bottom of the
jug, since this would prevent the steam
escaping. Froth the milk until the vol-
ume has at least doubled.
0
To stop frothing, turn the Selection dial
for steam and hot water (Fig. 1, D) to
the position and remove the jug
(Fig. 17)
.
1
Caution! Danger of scalding from hot
milk spray! Switch the steam off,
before removing the jug with the
frothed milk.
0
To finish steam mode, press the "Steam
Pre-selector" key (Fig. 3, g)
. The
indicator goes out.
The coffee machine is now ready for
making coffee again.
0
Each time you have frothed milk, let
off some hot water through the nozzle
for a short time by setting the Selec-
tion dial for steam and hot water (Fig.
1, D) to the
position. This is nec-
essary to prevent milk residues drying
inside the nozzle, and thereby blocking
it. Use a suitable container to catch the
water.
0
Remove the frothing aid after each use
(Fig. 18)
and flush the milk residues
away under running water. Wipe the
steam nozzle off with a damp cloth.
Summary of Contents for CF 2..
