English
36
Assembly Overview
1 Spacer tube
2 Mounting bar
3 Baldachin
4 Motor housing
5 Pull chain for setting the power level
6 Fan blade
7 3-part lamp attachment
8 Pull chain for the lighting (On/Off)
9 LED luminous elements
10 Mounting bracket
11 Switch for setting the rotation direction (summer/winter
operation)
Unpacking the Device
1. Remove the device from its packaging.
2. Remove all of the packaging material such as foils, filling
material, cable holders and cardboard packaging.
3. Check the scope of delivery.
4. Check the appliance for any transport damage to prevent
a hazard.
NOTE:
There may still be dust or production residues on the sur-
face of the device. We recommend that you quickly wipe
off the housing with a damp cloth.
Scope of Delivery
Please refer to the picture on page 5.
No. Quantity Description
1
5
Fan blade
2
1
3-part lamp attachment
3
1
Motor housing
4
1
Spacer tube
5
2
Pull chain
6
1
Suction cup for easy installation/unin-
stallation of the illuminant
7
3
LED luminous elements
(GU10, 220 - 240 V, 5 W)
8
2 each
Screw (M5*50), dowel, washer and
retainer ring
9
1
Baldachin with mounting bar
10
15 each
Screw (M5*15) and washer
11
5
Mounting bracket
Assembly Instructions
CAUTION:
•
Important!
The ceiling must be suitable to carry the
weight of the fan. Suspended ceilings are not suitable
for installation.
• Check beforehand for any cables hidden behind the
ceiling that could be damaged by installation!
WARNING: During installation
Switch off the home circuit breaker of the power supply line
to which to connect the device.
Please also refer to the pictures on page 3 and page 4.
1. Chose a suitable spot on the ceiling, taking into consider-
ation the wingspread of the fan blades.
2. Remove the mounting bar (2) from the baldachin (3).
3. There are two methods for attaching the mounting bar:
a) Wooden ceiling/beam: Attach the mounting bar us-
ing both long screws (M5*50) and the corresponding
washers and retainer rings.
b) Concrete ceiling: Mark the two positions in the slot-
ted holes using a pencil. Drill the installation holes for
the dowels. Insert the dowels into the holes. Attach
the mounting bar using both long screws (M5*50)
and the corresponding washers and retainer rings.
NOTE:
Use special caution when installing the fan to a con-
crete ceiling. In order to facilitate a secure installation,
stronger screws and dowels than those provided might
be necessary.
4. Connect the electrical wires from the ceiling to the termi-
nal strip in the mounting bar.
Color of electrical wire
Connection to
Brown or black (phase)
L
Blue (neutral)
N
Green yellow
(protective ground)
(Ground)
5. Remove the screw from the spacer tube (1). (See page 4 / 1)
6. Pull down the black cap and remove the pin. (See page 4 / 2)
7. Remove the safety clip from the motor housing (4) and
then remove the bolt. Slightly unscrew the two screws
located next to the bolt. (See page 4 / 3)
8. Guide the connection cable from the motor housing
through the baldachin (3). (See page 4 / 4)
9. Guide the connection cable from the motor housing
through the spacer tube. (See page 4 / 5)
10. Reinsert the pin into the spacer tube. Then reattach the
black cap using the screw. (See page 4 / 6)
11. Position the other end of the spacer tube in the fixture
of the motor housing. Reinsert the bolt and secure it
with the washer and safety clip. Tighten the two screws
located next to the bolt until hand-tight. (See page 4 / 7)
