background image

Use Previous and Next to switch

between the basic settings and to

change their value.
Use OK to enter the selected setting and

to confirm changing its value.

How to enter setting mode

You can enter setting mode before

starting a programme. You cannot enter

setting mode while the programme is

running.

To enter setting mode, press and hold
simultaneously 

 and 

 for

about 3 seconds.

The lights related to the PreviousOK

and Next are on.

How to change a setting

Make sure the appliance is in setting

mode.

1. Use Previous or Next to select the

bar of the ECOMETER dedicated to

the desired setting.

• The bar of the ECOMETER

dedicated to the chosen setting

flashes.

• The display shows the current

setting value.

2. Press OK to enter the setting.

• The bar of the ECOMETER

dedicated to the chosen setting is

on. The other bars are off.

• The current setting value flashes.

3. Press Previous or Next to change

the value.

4. Press OK to confirm the setting.

• The new setting is saved.

• The appliance returns to the basic

settings list.

5. Press and hold simultaneously

 and 

 for about 3

seconds to exit setting mode.

The appliance returns to the programme

selection.

The saved settings remain valid until you

change them again.

7. BEFORE FIRST USE

1. Make sure that the current level of

the water softener agrees with the

hardness of the water supply. If

not, adjust the level of the water

softener.

2. Fill the salt container.

3. Fill the rinse aid dispenser.

4. Open the water tap.

5. Start the programme Quick to

remove any residuals from the

manufacturing process. Do not use

detergent and do not put dishes in

the baskets.

After starting the programme, the

appliance recharges the resin in the

water softener for up to 5 minutes. The

washing phase starts only after this

procedure is complete. The procedure is

repeated periodically.

7.1 The salt container

CAUTION!

Use rough salt designed for

dishwashers only. Fine salt

increases the risk of

corrosion.

The salt is used to recharge the resin in

the water softener and to assure good

washing results in daily use.

How to fill the salt container

1. Turn the cap of the salt container

counterclockwise and remove it.

2. Put 1 litre of water in the salt

container (only for the first time).

3. Fill the salt container with dishwasher

salt (until it is full).

www.aeg.com

14

Summary of Contents for FSS63607P





























Reviews: