background image

Once you have checked the appliance,

deactivate and activate the appliance. If

the problem occurs again, contact an

Authorised Service Centre.
For alarm codes not described in the

table, contact an Authorised Service

Centre.

WARNING!

We do not recommend using

the appliance until the

problem has been

completely fixed. Unplug the

appliance and do not plug it

in again until you are certain

that it operates correctly.

11.1 The product number

code (PNC)

If you contact an Authorised Service

Centre, you need to provide the product

number code of your appliance.

The PNC can be found on the rating

plate on the appliance door. You can

also check the PNC on the control panel.
Before checking the PNC, make sure the

appliance is in the programme selection.

1. Press and hold simultaneously 

and 

 for about 3 seconds.

The display shows the PNC of your

appliance.

2. To exit the PNC presentation, press

and hold simultaneously   and 

for about 3 seconds.

The appliance returns to the programme

selection.

11.2 The washing and drying results are not satisfactory

Problem

Possible cause and solution

Poor washing results.

• Refer to "Daily use""Hints and tips" and the basket

loading leaflet.

• Use more intensive washing programme.

• Activate the SprayZone option to wash items with

heavy or stubborn soil.

• Activate the ExtraPower option to improve the washing

results of a selected programme.

• Clean spray arm jets and filter. Refer to "Care and

Cleaning".

Poor drying results.

• Tableware was left for too long inside the closed appli‐

ance. Activate AirDry to set the automatic opening of

the door and to improve the drying performance.

• There is no rinse aid or the dosage of rinse aid is not

sufficient. Fill the rinse aid dispenser or set the level of

rinse aid to a higher level.

• The quality of the rinse aid can be the cause.

• We recommend to use rinse aid always, even in com‐

bination with multi-tablets.

• Plastic items may need to be towel dried.

• The programme does not have the drying phase. Re‐

fer to "Programmes overview".

There are whitish streaks or

bluish layers on glasses and

dishes.

• The released quantity of rinse aid is too high. Adjust

the rinse aid level to a lower level.

• The quantity of detergent is too high.

ENGLISH

25

Summary of Contents for FSS63607P





























Reviews: