background image

compliance with the conditions specified in

overvoltage category III must be guaranteed. The

earth cable is excluded from this.

When you route the mains cable, make sure that the

cable doesn't come into direct contact (for example

using insulating sleeving) with parts that can reach

temperatures of more than 50°C above room

temperature.

WARNING: Use only hob guards designed by the

manufacturer of the cooking appliance or indicated by

the manufacturer of the appliance in the instructions

for use as suitable or hob guards incorporated in the

appliance. The use of inappropriate guards can cause

accidents.

2. SAFETY INSTRUCTIONS

This appliance is suitable for the
following markets:  FR

2.1 Installation

WARNING!

Only a qualified person must

install this appliance.

WARNING!

Risk of injury or damage to

the appliance.

• Remove all the packaging.

• Do not install or use a damaged

appliance.

• Follow the installation instructions

supplied with the appliance.

• Keep the minimum distance from

other appliances and units.

• Always take care when moving the

appliance as it is heavy. Always use

safety gloves and enclosed footwear.

• Seal the cut surfaces with a sealant to

prevent moisture from causing

swelling.

• Protect the bottom of the appliance

from steam and moisture.

• Do not install the appliance next to a

door or under a window. This

prevents hot cookware from falling

from the appliance when the door or

the window is opened.

• If the appliance is installed above

drawers make sure that the space,

between the bottom of the appliance

and the upper drawer is sufficient for

air circulation.

• The bottom of the appliance can get

hot. Install a non-combustible

separation panel under the appliance

to prevent access to the bottom.

2.2 Electrical Connection

WARNING!

Risk of fire and electric

shock.

• All electrical connections should be

made by a qualified electrician.

• The appliance must be earthed.

• Before carrying out any operation

make sure that the appliance is

disconnected from the power supply.

• Make sure that the parameters on the

rating plate are compatible with the

electrical ratings of the mains power

supply.

• Make sure the appliance is installed

correctly. Loose and incorrect

electricity mains cable or plug (if

ENGLISH

5

Summary of Contents for HKB63320NB





















Reviews: