g
23
Overload cut-out
The appliance is equipped with an
overload cut-out, which switches the
appliance off if it starts to overheat,
protecting the unit from damage.
When this happens, the overload cut-
out reset button (Fig. 1/N) jumps out.
1
If this happens, proceed as follows.
Failure to follow this procedure can
result in damage to the appliance,
which is not covered by the guarantee.
0
Allow the appliance to cool down for
at least 15 seconds.
0
Turn the speed selector (Fig. 1/I) left to
"0" position (Fig. 16/
①
).
0
Remove the mix container or all-pur-
pose bowl (Fig. 16/
②
and
③
), as descri-
bed at the relevant point in these
operating instructions.
0
Remove the mains plug from the
socket (Fig. 17/
①
).
0
Lay the appliance on its back to gain
access to the bottom (Fig. 17/
②
).
0
Press the overload cut-out reset button
(Fig. 1/N) on the bottom of the appli-
ance. If the appliance has cooled down
sufficiently, the button will engage
(Fig. 17/
③
). If it jumps back out, allow
the appliance to cool down a little lon-
ger, then repeat the process.
0
Once the reset button has engaged,
put the appliance back to its normal
working position (Fig. 18/
①
).
0
Plug the power lead back into the
mains socket (Fig. 18/
②
).
0
Replace the mix container or all-pur-
pose bowl (Fig. 18/
③
and
④
), as descri-
bed at the relevant point in these
operating instructions.
0
The appliance is now ready for use
again. Turn the speed selector to the
right to the required position (Fig.
18/
⑤
) and continue with the function
that was interrupted.
Mixer
The mixer is used to prepare a wide
range of mixed drinks, to crush ice,
reduce fruit and vegetables, etc.
Preparing mixer
In order to fit the mix container, the
safety cover for the mixer drive (figs.
1/T and 4) must be removed.
0
Turn the safety cover
clockwise
and
remove.
– The red warning lamp (fig. 4/a)
flashes.
0
Place the mix container (figs. 1/B and
2) on the mixer drive (arrow
on
arrow )
and
turn
counter-clock-
wise
to the stop. The mix container is
heard to engage. The two black arrows
must coincide.
– The red warning lamp (fig. 4/a)
extinguishes.
0
Only KM 850:
Place mixer cover (figs.
1/C and 3) on mix container and turn
until the nose of the cover is directly
above the handle. The cover can be
heard to engage.
3
The mixer can only be switched on
when the container and cover are fit-
ted correctly.
0
Only KM 880:
Place mixer cover on
mix container.
3
The mixer can only be switched on
when the container is fitted correctly.
0
Fit closing cover (fig. 1/D) and lock.
Operating mixer
0
Open cover (fig. 1/C) and fill all ingre-
dients required in the container.
Caution:
Do not exceed maximum fill-
ing volume of 1.5 litres!
3
During operation further ingredients
can be added through the filling inlet.
The sealing cover (fig. 1/D) can also be
used as a filling beaker for this pur-
pose. Close the filling inlet again
KM850_de_nl.book Seite 23 Donnerstag, 29. Juli 2004 7:08 19
Summary of Contents for KM 8.. Assistent
