background image

When using liquid

detergent, make sure that

the special container for

liquid detergent is

inserted. Refer to the

"Manual filling the

detergent and additives"

paragraph in this chapter.

The liquid detergent

container is supplied

inside the drum.

Manual

 Manual compartment for liquid

additives (fabric softener, fabric

conditioner, starch).

 Maximum level for detergent/

additives quantity.

9.3 AutoDose basic setting

The factory pre-set doses for a large

load are 90 ml for detergent tank and

25 ml for fabric softener tank: the

optimal configuration to meet majority

of use condition. Based on this

setting, the appliance will calculate

the precise dosage for each wash.

However, under extreme conditions (very

soft or very hard water) and particular

type of detergent (such as super

compact), we recommend to adjust the

pre-set dosage by following the

indication given on detergent and fabric

softener container: e.g when using super

compact detergent you may need to

reduce the pre-set dosage considerably.
If the washing results are not satisfying

or there is too much foam during

washing, you may need to change the

factory setting. Read in the paragraph

'AutoDose configuration mode' how to

change the basic setting, but before:
1. Identify the water hardness level.

Check the water hardness level in

your area. The levels are generally

indicated as: soft, medium and hard.

If necessary, please contact your

local water authority to check the

water hardness in your area.

2. Identify the customized detergent

dosage.

Check the label in the detergent/

fabric softener container suggesting

the quantity to use. This suggestion

is measured combining three

different factors:

• Water hardness level (see the

following table);

• Normal soil level;

• Rated capacity of the appliance

(e.g. maximum load capacity 9

kg). If the rated capacity on the

product container refers to lower

capacity appliances, the

customized dosage should be

increased.

Water hardness levels

Levels

Water hardness range

°f

1)

°d

2)

°e

3)

mmol/l

ppm

Soft

<15

<8

<10

<1.4

<140

Medium

4)

15 - 25

8 - 14

0 - 17

1.5 - 2.5

150 - 250

Hard

>25

>14

>17

>2.5

>250

1) French degrees
2) German degrees
3) English degrees
4) Factory setting, able to satisfy most of the use conditions.

ENGLISH

25

Summary of Contents for L7FEE945CA

































































Reviews: