background image

 - The mains supply is unstable.

Wait until the mains supply is stable.

 - No communication between

electronic elements of the appliance.

Switch it off and switch on again.

The programme was not finished

properly or the appliance stopped

too early. If the alarm code appears

again, contact the Authorised Service

Centre.

 - The anti-flood device is on.

Disconnect the appliance and close

the water tap. Contact the Authorised

Service Centre.

WARNING!

Deactivate the appliance

before carrying out any

check.

16.2 

Possible failures

Problem

Possible solution

The programme does

not start.

• Make sure that the mains plug is connected to the mains

socket.

• Make sure that the appliance door is closed.
• Make sure that there is no damaged fuse in the fuse box.
• Make sure that the Inicio/Pausa has been touched.
• If the delay start is set, cancel the setting or wait for the end

of countdown.

• Deactivate the Child Lock function if it is on.

The appliance does not

fill with water properly.

• Make sure that the water tap is open.
• Make sure that the pressure of the water supply is not too

low. For this information, contact your local water authority.

• Make sure that the water tap is not clogged.
• Make sure that the inlet hose has no kinks, damages or

bends.

• Make sure that the connection of the water inlet hose is

correct.

• Make sure that the filter of the inlet hose and the filter of

the valve are not clogged. Refer to 'Care and cleaning'.

The appliance fills with
water and drains immedi-
ately

• Make sure that the drain hose is in the correct position. The

hose may be positioned too low. Refer to "Installation in-
struction".

ENGLISH

39

Summary of Contents for L7WEE861

















































Reviews: