background image

5. Without the plastic hose guide, to

a sink spigot - Put the drain hose in

the spigot and tighten it with a clamp.

Refer to the illustration.

Make sure that the drain

hose makes a loop to

prevent particles going into

the appliance from the sink.

6. Position the hose directly to a built-

in drain pipe in the room wall and

tighten it with a clamp.

5.6 Electrical connection

At the end of installation you can connect

the mains plug to the mains socket.

The rating plate and the 'Technical Data'

chapter indicate the necessary electrical

ratings. Make sure that they are

compatible with the mains power supply.
Check that your domestic electrical

installation can take the maximum load

required, also taking into account any

other appliances in use.
Connect the appliance to an earthed

socket.

The power supply cable must be easily

accessible after installing the appliance.
For any electrical work required to install

this appliance, contact our Authorised

Service Centre.
The manufacturer does not accept any

responsibility for damage or injury

through failure to comply with the above

safety precaution.

ENGLISH

13

Summary of Contents for L8FQS967C2





























































Reviews: