AEG PROTECT A 1000 Operating Instrctions Download

Page: 17 / 18

Trouble shooting

SYMPTOM

CAUSE

REMEDY

Missing battery

Charge battery up to 4 hours

Battery fault

Replace with the same type of
battery

No LED display
on the front panel

Power switch not pressed

Turn on the switch again

Alarm buzzer
beeps
continuously
when AC supply
is normal

UPS overload

Verify that the load matches the
UPS capability as specified in
the specs

UPS overload

Remove some non-critical load

Battery voltage is too low

Charge battery 4 hours or more

When power
failure, back-up
time is short

Battery fault due to high
temperature operational
environment, or improper
treatment of battery

Replace with the same type of
battery

Fuse is blown

Replace with the same type of
fuse

Mains normal but
LED is flashing

Power cable is loose

Reconnect the power cable
properly

Software not properly
installed

Check the settings of the
software

Communication
lost between UPS
and computer.

Cable not properly connected Check if the RS232-cable is

properly connected to COM1 /
COM2 of the computer and
reconfirm the settings once
again

If any abnormal situations occur that are not listed above,
please call the service centre immediately.

Summary of Contents for PROTECT A 1000



















Search results

Summary of Contents for PROTECT A 1000

Reviews:

Related manuals for PROTECT A 1000

Brands by name

Popular brands

AEG PROTECT A 1000, Operating Instrctions

Search results

Summary of Contents for PROTECT A 1000

Reviews:

Related manuals for PROTECT A 1000

Brands by name

Popular brands