AEI DK-2891A, User Manual

OUTPUT OPERATION ANNOUNCER                                                          (Location 72)

(1) LOCATION 

Key in Location

(2) FUNCTION MODES FOR OUTPUT ANNOUNCER

Output announcer gives notification beep on the operation status of the outputs. There are two 

notification modes available for the selection.The notification is also OFF while the Pacifier Tone OFF 

mode in the Location 71 is selected.

      --- 

No Notification

The output operation notification is OFF but does note affect the normal pacifier tones.   

    --- 

1 Second Long Notification -- (Default)

 --- 

2 Short Beeps Notification

2 short beeps notification is given when the output relay activates.

(3) VALIDATION

Press  

key once. Two-beep confirms the entry

STATUS LED FLASHING ON-OFF DURING STANDBY                               (Location 73)

(1) LOCATION 

Key in Location 

(2) FUNCTION MODES FOR STANDBY FLASHING LIGHT

Some people find the flashing light of the status LED (the amber LED) is annoying during standby, 

especially at the night time. The standby flashing can be ON-OFF with the setting here.



 --- 

Standby Flashing ON -- (Default)

The Status LED gives Standby Flashing all the time. It also gives the light indications showing 

the operation status of the system.



  --- 

Standby Flashing OFF

The Standby Flashing is OFF but it does not affect the system status indications.

(3) VALIDATION

Press 

key once. Two-beep confirms the entry

FUNCTION MODES

VALIDATION

LOCATION



 or 







(2)

(3)

(1)

FUNCTION MODES

VALIDATION

LOCATION



 or 







(2)

(3)

(1)







5) Example 5 -- Delete An User Code & / or EM Card (for O/P 1 or 2) :

i) Delete An User Code or A Lost EM Card

         (a)     (b)         (c)        (d)
(a) Key in the User Group that the User ID belongs to. “10” for Group 1 and “20” for Group 2
(b) Key in “5” that is the Command Code for making a deletion
(c)

Key in the User ID that stored the User Code, the lost EM card or the EM Card+User Code

(d) Press the # key. Two-beep confirms a valid entry and the Code and/or Card in that User ID is 

cleared      

ii) Delete an EM Card

          (a)      (b)             (c)           (d)
(a) Key in the User Group that the EM Card belongs to. “1 0” for Group 1 and “2 0” for Group 2
(b) Key in “5” that is the Command Code for making a deletion
(c) Read the EM card. One-beep confirms the reading. Read the Card only also makes a valid deletion 

to the Card working with the Common User Code or the Secondary User Code

(d) Press the # key. Two-beep confirms a valid entry. The EM Card in that User ID is cleared. Key in 

the User ID is not required. 

6) Example 6 – Clear The Whole Group of Users :

Whole group of users including the Codes and Cards can be cleared with the following command.

          (a)              (b)           (c)
(a) The User Group 1 – “10” is selected to be cleared.  “20” for Group 2
(b) Key in the Group Deletion Command, 0 9 9 9
(c) Confirm the deletion with #. All the User Codes and Cards in Group 1 are cleared. It takes few 

seconds to a minute to complete depending on the data stored.

User ID

Read Card

NOTE:

In multi-station operation, the output announcer only goes to the keypad that has been operated but 

not all the keypads in the system.





1 second notification beep is given when the output relay activates. It is prepared to notify 

the person outside the door when the lock is released and the door can be opened. It is 

good for door lock that gives no sound when it activates, such as a magnetic lock.