background image

8

 

AEM Air Intake System Warranty Policy

 

AEM

®

 warrants that its intake systems will last for the life of your vehicle. AEM

®

 will not honor this warranty due to me-

chanical damage (i.e. improper installation or fitment), damage from misuse, accidents or flying debris. AEM

®

 will not 

warrant its powder coating if the finish has been cleaned with a hydrocarbon-based solvent. The powder coating should 
only be cleaned with a mild soap and water solution. Proof of purchase of both the vehicle and AEM

®

 intake system is 

required for redemption of a warranty claim.   
 
This warranty is limited to the repair or replacement of the AEM

®

 part. In no event shall this warranty exceed the original 

purchase price of the AEM

®

 part nor shall AEM

®

 be responsible for special, incidental or consequential damages or cost 

incurred due to the failure of this product. Warranty claims to AEM

®

 must be transportation prepaid and accompanied 

with dated proof of purchase. This warranty applies only to the original purchaser of product and is nontransferable.  Im-
proper use or installation, use for racing, accident, abuse, unauthorized repairs or alterations voids this warranty.  AEM

®

 

disclaims any liability for consequential damages due to breach of any written or implied warranty on all products manu-
factured by AEM

®

. Warranty returns will only be accepted by AEM

®

 when accompanied by a valid Return Merchandise 

Authorization (RMA) number. Credit for defective products will be issued pending inspection. Product must be received 
by AEM

®

 within 30 days of the date RMA is issued.   

 
If you have a warranty issue, please call (800) 992-3000 and our customer service department will assist you. A 

proof of purchase is required for all AEM

®

 warranty claims.

 

10

-

107A  3/8/18

 

Summary of Contents for 21-814C









Reviews: