5-78
BA 418-12 * 1.0 * 418_12_5_Bedienung.fm
5 Operation
Fitting attachments from other manufacturers (option)
Quickhitch facilities for attachments from other manufacturers
The following quickhitch facilities can be purchased from your distributor
and installed by an authorized service center.
Quickhitch facility for attachments
- with EURO quickcoupler
- with WEIDEMANN support
- with SKID STEER support
- with MATBRO support
- with MANITOU support
•
Important!
Only attachments may be used on quickhitch facilities from other
manufacturers that are approved for this purpose and that have a
load diagram approved for the attachment
.
-
– see chapter 3 " Attachments for WEIDEMANN quickhitch facility"
on page 3-18
-
– see chapter 3 " Attachments for EURO quickhitch facility
(optional)" on page 3-20
-
– see chapter 3 " Attachments for SKID STEER quickhitch facility
(optional)" on page 3-22
• If other attachments are used, conformity (stability test) in accordance
with the EC machine directive or the EN 1459 and EN 474-3 standard
must be checked and documented by an authorized service center.
• Warranty and the operation license become void if non-approved
attachments are installed, or if parts of the quickhitch or attachment
(with a prescribed condition or quality, or the operation of which can
put persons at risk) are subsequently modified or replaced.
• In addition to the Operator’s Manual, observe and instruct the operator
in all other generally applicable, legal and other mandatory regulations
relevant to accident prevention and environmental protection.
• See the following pages for the stability check.
• In the case of non-EU countries, follow and apply the national regulations
of these countries.
Important information on fitting attachments from other
manufacturers
WARNING
Accident hazard if the attachments are not locked!
Can cause serious injury or death.
►
Check whether the lock pins
E on both sides are visible
in the
mounting bores of the attachment.
E
Fig. 263
Summary of Contents for 418-12
