BA 418-12 * 1.0 * 418_12_5_Bedienung.fm
5-97
Operation 5
Important information on picking up loads
• Approach the material as closely as possible!
• Always approach the material with the machine wheels in straight-
ahead position!
• Always load on firm and level ground with sufficient load-bearing
capacity only!
• Never raise a load with only one fork arm!
• Move the fork tines all the way through under the pallets, as far as they
will go, so that the load is picked up the nearest possible to the fork
frame!
• Move under the load with the straight fork tines as far apart as possible
and at an equal distance from the left and right side of the load!
Important information on load transport
WARNING
Danger of accident due to restricted line-of-sight during transport!
Failure to observe this can cause serious injury or death.
►
Only use approved attachments
►
Transport the cargo in the transport position about 175 mm (6.8 in).
►
Check the line of sight and adjust the mirrors.
►
If the line-of-sight cannot be ensured, use the camera option.
• Always tilt in the attachment a little (toward the machine) for transport!
• Always transport the load close to the ground!
• Bear in mind the overload warning device!
• Always adapt the transport speed to the load you are transporting and
to the ground conditions!
• Never leave the machine with the load raised!
• Do not lower the loader unit from a high fork tine position with an
extended telescopic boom – always retract the telescopic boom first!
• On slopes, the load must be on the uphill side of the machine/
attachment. Drive the machine backward on sloping terrain to prevent
the load from falling off and the machine from tilting forward when
braking.
• When transporting large bulk loads perform backward machine travel
for improved visibility!
• Observe the load-bearing capacity of bridges, basement ceilings,
vaults, etc., before moving the machine on them!
• Bear in mind the clearances of underpasses, tunnels, gates, etc.
before machine travel through or under them!
126801d0.ai
Fig. 287
Summary of Contents for 418-12
