8-14
BA 418-12 * 1.0 * 418_12_8_Betriebsstoerung.fm
8 Malfunctions
516500
24
'D002: CAN- Bus joystick logic error
516699
02
P006: OMD- CRC error in the data flash
516699
12
P006: OMD- CRC error in the system flash
516699
13
P006: OMD- calibration faulty / not executed
516699
14
P006: OMD- control unit not found
516699
22
P006: OMD- error in the digital switching output
516699
24
P006: OMD- redundancy error of the sensor cells
516699
26
P006: OMD- sensor cell outside of the range
517104
02
B105: three-point potentiometer – both signals, incorrect or implausible data
517104
12
B105 three-point potentiometer - Internal error of the control unit
517104
26
B105 three-point potentiometer -both signals outside of the valid value range
517113
02
B028: angle sensor of the tilt cylinder – both signal - data incorrect or not plausible
517113
12
B028: tilt cylinder angle sensor - control error
517113
26
B028: tilt cylinder angle sensor for both signals - Signal outside of the valid range
517551
19
E60: system function monitoring, control unit flash memory – memory error – data reception with
active error status
517551
24
AppInit: system function monitoring, control software object initialization – wrong machine configuration
(object initialization failed) – logical error (software error)
517900
12
Control unit error
517901
12
Control unit error
517902
2
Control unit - HAST or PTC data faulty or not plausible
517903
2
System function monitoring, control unit, data faulty or not plausible
517903
27
System function monitoring, control unit, open wiring or short circuit to ground
517904
09
TIME: system function monitoring, control unit Central Processor Unit – timeout/abnormal clock rate
517904
16
UBAT: System function monitoring, monitoring control unit -Signal 1- Signal very low
SPN
FMI Description of critical errors for the drive electronics
Summary of Contents for 418-12
