BA 418-12 * 1.0 * 418_12_5_Bedienung.fm
5-15
Operation 5
Select the travel direction, start, stop
Selecting a travel direction and starting machine travel
1. Select a speed
– see chapter 5 " Travel speed increase/reduction/
2. Press down the brake/inching pedal with force.
3. Release the parking brake.
4. Select the travel direction with the rocker switch
push
forward or backward on the joystick.
➥
V
= forwards - Symbol
D/1
appears in the digital display
➥
V
= reverse operation - Symbol
D/2
appears in the digital display
5. Slowly release the brake-inch pedal and actuate the gas pedal.
6. Test the brakes at low speed.
Information
If the travel direction selection is not accepted (no function), the
button
112/N
was accidentally pressed when operating the travel direction
selection (only possible with the KRAMER joystick) or the hand brake is
not yet activated.
Information
The travel direction change (forwards / reverse operation) can be performed
from any travel speed increase/reduction, but for safety reasons is first
activated once the travel speed has been reduced to 3 km/h.
Stopping the machine
1. Reduce engine speed. To do this: remove your foot from the
accelerator pedal.
2. Stop the machine with the service brake.
3. Select the travel direction with the button
or switch the rocker
switch into the
neutral position.
➥
Symbol
D/3
appears in the digital display.
4. Apply the parking brake.
Fig. 190
1
2
Design A
Design B
V
R
N
V
R
N
3
D
D
D
Summary of Contents for 418-12
