BA 418-12 * 1.0 * 418_12_5_Bedienung.fm
5-139
Operation 5
Connect attachment to the rear flat connector plugs
1. Lower the loader unit and apply the parking brake.
2. Stop the engine, but do
not
switch off ignition.
3. Release the hydraulic pressure in the flat connector plugs. To do this,
and button
in succession and hold each one
down for about 8 seconds.
➥
Pressure in quick couplers is released.
4. Switch off the starter and remove the starting key.
5. Clean the flat connector plugs of dirt and dust.
6. Connect the hose pipes of the attachment to flat connector plugs
E
(rear side of the frame).
7. Commission flat connector plugs
E
connector plugs in the rear" on page 5-139
.
Information
The hose pipes can be loosened from the flat connector plugs
E
but not
re-attached if the pressure in the hydraulic lines is not depleted.
►
Release the pressure in the system and the pressure lines when
installing or removing an attachment.
Operation of the flat connector plugs in the rear
1. Apply the parking brake.
2. Start the diesel engine.
3. Switch on the auxiliary control circuits depending on the direction of
rotation. To do this, briefly press the touch button
or
.
➥
The LED illuminates in the corresponding touch button.
➥
Symbol
appears in the digital display.
4. Switch off the auxiliary control circuits. To do this, briefly press the
touch button
or
again.
➥
The LED in the touch button goes out.
➥
The symbol
G/4
goes out.
Information
Restart lock!
For safety reasons, the auxiliary control circuit is automatically deactivated
by switching the ignition off and on again.
This has to be reactivated when re-starting the auxiliary control circuit!
Fig. 331
E
4
Fig. 332
Summary of Contents for 418-12
