BA 418-12 * 1.0 * 418_12_3_Einleitung.fm
3-13
Introduction 3
Use of attachments
• The following quickhitch facilities can be installed on the vehicle:
- KRAMER quick coupler systems,
- WEIDEMANN quick coupler system,
- EURO quick coupler system,
- SKID STEER quickhitch facility,
- MANITOU quickhitch facility,
- MATBRO quickhitch facility.
• How the vehicle is used depends on the attachments available.
• The respective approved attachments for the quick coupler systems
with the corresponding requirements can be found in the following
tables. See page
–
• Also refer to the National Type Approval (Germany) or the Data
Confirmation (Germany) for fitting certified attachments and for the
specific requirements.
• When fitting attachments that are not listed in the National Type
Approval (Germany), the Data Confirmation (Germany) or the
registration documents, get in touch with a dealer for authorization
(warranty claims)! The EBE (individual operating permit) from the
competent national authorities is then required for this purpose.
• Warranty rights shall not apply if uncertified attachments or
attachments from other manufacturers are installed.
• Machine travel on public roads with a full bucket is prohibited.
• With a mounted attachment, the possible line-of-sight impairment must
also be observed
– see "Field of vision during road travel" on page 4-6
and
“Field of vision during work operation” on page 4-7
Information
The application of attachments that are not listed for the corresponding
quickhitch system must be tested and documented for compliance
(stability inspection) according to the EC machine directive or the
standard EN 1459 by an authorized specialized workshop in the EU
member states (load-bearing capacity diagram)
– see chapter 5 " Fitting attachments from other manufacturers (option)"
on page 5-78
In the case of non-EU countries, follow and apply the national regulations
of these countries.
Information
This Operator’s Manual only describes how to install, use and remove the
standard bucket, multipurpose bucket and pallet forks
attachments on the quickhitch facility" on page 5-66
.
For the description of the function and application of other attachments,
refer to the operator’s manuals of these attachments.
Summary of Contents for 418-12
