3-18
BA 418-12 * 1.0 * 418_12_3_Einleitung.fm
3 Introduction
Attachments for WEIDEMANN quickhitch facility
Important information on the quickhitch facility and attachments
The machine manufacturer currently has only released the attachments
listed on page
for this quickhitch facility!
NOTICE
Avoid damage to the machine due to the use of uncertified attachments:
►
Use only attachments that are certified for the existing quickhitch
system and that are fitted with a load diagram certified for the specific
attachment.
►
If uncertified attachments are installed, or if parts of the quickhitch
facility or attachment are subsequently modified or replaced, the
operation license and the warranty become void.
►
In addition to the Operator’s Manual, observe and instruct the operator
in all other generally applicable, legal and other mandatory regulations
relevant to accident prevention and environmental protection.
►
Please contact your dealer if you require more information on the
quickhitch and the specific attachments.
Information
The use of attachments that are not listed for the corresponding quick-
hitch systems must be tested and documented for compliance (stability
inspection) according to the EC machine directive or the standard EN
1459 by an authorized specialized workshop in the EU member states
(load-bearing capacity diagram)
– see chapter 5 " Fitting attachments
from other manufacturers (option)" on page 5-78
.
In the case of non-EU countries, follow and apply the national regulations
of these countries.
Information
For trips on public roads in the Federal Republic of Germany, only the
attachments that are described in the following table on page
are
permitted.
Attachments that are not approved for use in public traffic must be
removed and transported to the site of application with a suitable transport
vehicle.
Furthermore, the possible line-of-sight impairment must be taken into
consideration with a mounted attachment
and
“Field of vision during work operation” on
.
Summary of Contents for 418-12
