background image

5

     

   FUNCTION SELECTOR SWITCH

 OFF

Off position

 

 V

DC and AC voltages up to 600V, with high impedance: 10M

  Velec

AC voltages up to 600V, with low impedance: 270k

Note:

 Also available on DC voltage.

  

Hz

(C.A 5220 only)
Frequencies of voltages, up to 200kHz

 

 

Continuity sound test for a resistance R 

 40

, and

resistance measurements up to 40M

Note: 

The continuity test 

 is selected automatically

when the instrument is switched on.

  

Diode test. Measurement of the voltage of the junction in
forward direction

   

Capacitances up to 40µF

    A

(C.A 5220 only)
10A

AC/DC

 current ranges (via the 10A terminal)

  mA

(C.A 5220 only)
Current ranges up to 400mA

AC/DC

 (via the + terminal)

     

   TERMINALS

Ø 4mm safety terminals

  COM : 

common, black

  + :

 red

  10A

 (C.A 5220 only) : red lead for the 10A

AC/DC

 ranges

3 - DC AND AC VOLTAGE

Connect the leads to the multimeter and connect it in parallel to the
circuit to be tested.
Place the selector switch on voltmeter (V) function (high
impedance). The instrument is in AC mode. Press the AC/DC button
to select DC and vice versa.
Automatic range selection: read the measured value.
Freeze the value, by pressing the HOLD button.

C.A 5220 only

If necessary, press the following buttons:

  

RANGE to select the ranges manually

  

MIN/MAX to read the min or max values

  

 to switch on the backlight of the display

Summary of Contents for C.A 5210













Reviews: