background image

The Aeotec Home Energy Meter can report wattage energy usage or kWh energy usage to a control point 

when requested. If this function is supported by the controller point, the energy consumption will be 

displayed in the user interface of the control point. (The specific Z-Wave commands supporting energy 

monitoring are the Meter Command Class)

Node Information Frame

NI

 The Node Information Frame is the business card of a Z-Wave device. It contains information 

about the device type and the technical capabilities. The inclusion and exclusion of the device is confirmed 

by sending out a Node Information Frame. Beside this it may be needed for certain network operations to 

send out a Node Information Frame.

A single click on the little button on the backside sends a Node Information Frame.

Associations

A

 Z-Wave devices control other Z-Wave devices. The relationship between one device controlling 

another device is called association. In order to control a different device, the controlling device needs to 

maintain a list of devices that will receive controlling commands. These lists are called  association groups 

and they are always related to certain events (e.g. button pressed, sensor triggers, ...). In case the event 

happens all devices stored in the respective association group will receive a common wireless command.

Association Groups:

1 Receiver of all Reports (max. nodes in group: 5)

Configuration Parameters

Z-Wave products are supposed to work out of the box after inclusion, however certain configuration can 

adapt the function better to user needs or unlock further enhanced features.

IMPORTANT: Controllers may only allow to configure signed values. In order to set values in the range 128 

… 255 the value sent in the application shall be the desired value minus 256. For example: to set a 

parameter to 200? it may be needed to set a value of 200 minus 256 = minus 56. In case of two byte value 

the same logic applies: Values greater than 32768 may needed to be given as negative values too.

(c) 2012 Z-Wave Europe GmbH, Goldbachstr. 13, 09337 Hohenstein-Ernstthal, Germany, All rights reserved, www.zwaveeurope.com - pp 4 

Summary of Contents for AEO HEM2-100A











Reviews: