background image

 

         BC 2000

 

DIGITAL

 

Audio Routing, Mixing and Processing System for Program Production Centers 

 

 

 

HARDWARE MANUAL 

 

41 

Other characteristics and features. 
 

-

  Internal warning signal indicating a failure in one of the power supplies. If a failure occurs, the 

“ALARM” LED on the BC2240 controller board will light up. 

-

  Power feed circuit designed to support hot-swapping operations. 

 
Programming jumpers. 
 
This  board  has  a  series  of  internal  programming  jumpers  (PJ).  However,  these  jumpers  are 
configured at the factory and, in normal operation, do not need to be changed. 
 
Firmware modules. 
 
At the firmware level, this board is made up of the following modules: 
 

PIC microcontroller: manages board communications and start-up. 

FPGA programmable device: manages the TDM bus. 

 
The firmware versions can be brought up to date by using the ”BC2000D Firmware Upgrade” 
software application. 
 
BC2211 technical specifications. 
 
Synchronism output: 

-

  Type: TTL (Word-Clock). 

-

  Connector: 1.6-5.6 female coaxial. 

 
Coaxial interface: 

-

  Type: 75

 coaxial. 

-

  Nominal range: 50 m. 

-

  Connectors: 1.6-5.6 female. 

-

  Type of cable: 75 

 ±2 

 coaxial, attenuation less than 0.1 dB/m. 

 
Optical fiber interface: 

-

  Type: FDDI PMD. 

-

  Nominal  range:  2,000  meters  (if  your  installation  entails  a  range  greater  than  2000  meters, 

contact our sales department). 

-

  Type of fiber: 62.5 / 125 

µ

m MULTIMODE. 

-

  Transmission: LED, 1300 nm. 

 
General characteristics. 
 

-

  Approximate consumption: 8.5 watts. 

-

  Approximate dimensions: 

Front: 17 x 172 mm. 
Depth: 255 mm.

 

-

  Approximate weight: 310 grams. 

 

Characteristics are subject to change without notice. 

 

 
 

 
 

Summary of Contents for BC 2000



























































































Reviews: