background image

TF7038GB_A_NOT

 

 

COMPONENTS 

 

2.3.1. 

REFRIGERANT CIRCUIT COMPONENTS 

COMPRESSOR 
A hermetic inverter rotary piston compressor that is highly efficient and uses an energy-saving DC electric 
motor. Mounted on elastic vibration-damping compensators. 

COMPRESSOR INVERTER MODULE 
The inverter module infinitely controls the compressor speed using the sensor-controlled power 
specification on the system controller. This means the compressor motor is continually monitored and 
protected from damage. 

CONDENSER 
Featuring a plate structure (stainless steel, 1.4401). Featuring closed cellular insulation material on the 
outside to minimise heat loss. 

EVAPORATOR 
Featuring a plate structure (stainless steel, 1.4401). Featuring closed cellular insulation material on the 
outside to minimise heat loss and to prevent condensate formation. 

 

REFRIGERANT COLLECTOR 
A refrigerant collector ensures a bubble-free liquid upstream of the expansion valve in all performance 
ranges. 

FILTER DRYER 
A hermetic-mechanical filter dryer with cartridges made of ceramic and hygroscopic material retains 
impurities and any traces of moisture present in the cooling circuit. 

THERMOSTATIC EXPANSION VALVE 
The mechanical expansion valve with external pressure compensation regulates the gas flow to the 
evaporator depending on the thermal load to ensure the intake gas overheats to a sufficient degree. 

REFRIGERANT SIGHT GLASS WITH HUMIDITY INDICATOR 
Used to check the refrigerant fill level and any possible humidity in the cooling circuit. 

 

2.3.2. 

WATER CIRCUIT COMPONENTS 

 

SINK CIRCUIT (HOT 

WATER) 

SOURCE CIRCUIT 

(AWN BRINE 
CIRCUIT) 

WATER FILTER 

A steel filter net prevents the heat exchangers from clogging. 

 

DIFFERENTIAL PRESSURE CONTROLLER 
A differential pressure sensor allows continuous 
water circulation to be controlled in the AWN heat 
exchanger circuit. In the event of a fault, the 
cooling circuit is switched off. 

SAFETY VALVE (6 BAR) 

In the event of pressure faults in the brine and heating water pipes, a safety valve is triggered and 

excess pressure is released. This can be connected to a drain on site. 

Summary of Contents for CONNECT WP120





























Reviews: