AERMEC URHE CF Series, User Manual

User Manual - URX_CF and URHE_CF -

4

Introduction

The controller is the compact device 

that makes it possible to control units 
for single-circuit air-to-air condition-
ing.

 
  Pay special attention to the usage 

regulations marked by the word 
“DANGER” or “WARNING” or by the 
“safety symbols“, as failure to respect 
them may lead to harm to people 
and/or damage to the machine/prop-
erty.

•   For any problems not listed in this 

manual, contact your local After Sales 
Service immediately.

•  

The manufacturer cannot be held lia-
ble for any damage caused by the 
improper use of the machine, or by 
the partial or superficial reading of 
the information given in this manual.

•   Installation and maintenance must 

be carried out by expert and quali-
fied personnel, according to the legal 
requirements in force in the country of 
installation for the electrical/electron-
ic as well as air conditioning installa-
tions. Failing this, the manufactures 
declines any liability with regards to 
the safety of the product.

THE MANUFACTURER DECLINES ANY 
LIABILITY FOR DAMAGES TO PERSONS, 
ANIMALS OR PROPERTIES CAUSED 
BY THE  FAILURE TO  OBSERVE THE 
INSTRUCTIONS AND REGULATIONS 
INCLUDED IN THIS MANUAL.

Although during the design of the units, 
an appropriate analysis of the risks was 

carried out, pay ATTENTION to the picto-
grams on the machine that make reading 
the manual easier by drawing the read-
er's attention on the situations posing 
risks that cannot be avoided or sufficient-
ly limited by adopting protection meas-
ures and technical solutions.

G E N E R A L   D A N G E R   S I G N A L

Observe carefully all instruc-
tions next to the pictogram. 
Failure to observe the instruc-

tions can lead to risk situations with 
possible consequent damages to the 
operator's and users' health in general.

DANGEROUS VOLTAGE SIGN 
Observe carefully all instructions next to 
the pictogram. 
The sign shows the components of the 

unit or, in this manual, identifies 
actions that could cause electri-
cal risks.

GENERAL PROHIBITION SIGNAL
Carefully observe all instructions next to 
the pictogram that limit some actions to 
ensure greater safety for the operator.

MAIN WARRANTY 

CONDITIONS

•  The warranty does not include 
the payment for damages due 

to wrong installation of the unit by 

the operator.

•   The warranty does not include the 

payment for damages due to improp-
er use of the unit by the operator. 

•   The factory shall not be liable for 

incidents occurred to the installer 
or user, arising from wrong instal-
lation or improper use of the unit.

The warranty is not valid only in case:
•   ser vices and repairs are car-

r i e d   o u t   b y   n o n - a u t h o r i s e d 
p e r s o n n e l   a n d   c o m p a n i e s ;

• 

 t h e   u n i t   w a s   p r e v i o u s -

ly repaired or modified with 
n o n - o r i g i n a l   s p a r e   p a r t s ; 

• 

 n o   p r o p e r   m a i n t e n a n c e 

was carried out on the unit;

•   in case the instructions in this 

m a n u a l   w e r e   n o t   f o l l o w e d ;

•  i f   n o n - a u t h o r i s e d   m o d i f i -

c a t i o n s   w e r e   c a r r i e d   o u t .

N.B.:
The factory reserves the right to make 
any changes in order to improve its prod-
ucts at any time, and is not obliged to 
add these modifications to previously 
manufactured machines, those that have 
already been delivered or those under 
construction.
Warranty conditions are in any case sub-
ject to the general sales conditions that 
are in place when the contract is stipu-
lated.