INFLATION & ADJUSTMENTS
NOTE: BED MUST BE AT ROOM TEMPERATURE PRIOR TO INFLATING OR IT MAY CAUSE
AIR LEAKS.
NOTE: PRESSURE CAN VARY DEPENDING ON ROOM TEMPERATURE AND CONSUMER WEIGHT.
1. Place your rolled-up bed on the floor or other surface free of obstructions or sharp objects.
2. Make certain the Quick Air Release Valve is closed. If the release valve is open, close it by
using 2 thumbs to push cover and snap into valve. Be careful to avoid pushing valve cover
to the right or left as it snaps into the valve opening.
3. Remove the AC plug and cord from the plastic bag and
shrink wrap.
4. Plug into any standard polarized 120 Volt AC electrical outlet.
North American Electrical rating: 120 VAC 60 Hz 1.5 A.
(Note: 230 VAC product sold outside of North America). This
product has a polarized attachment plug (one blade is wider
than the other) as a safety feature. This plug will fit into a
polarized outlet only one way. If the plug does not fit fully in
the outlet, reverse the plug. If it still does not fit, contact a
qualified electrician. Never use with an extension cord unless
the plug can be fully inserted. Do not attempt to defeat this
safety feature.
5. On the Control Wand, press the UP arrow on the switch into the
“INFLATE” position to inflate your bed. Once bed has reached
desired firmness, return the switch to the off position “O”.
6. Lie on your bed and use the Control Wand to adjust the firmness
to your desired level. For a firmer bed, press the UP arrow on the
switch into the “INFLATE” position. For a softer bed, press the
down arrow “ADJUST” until desired firmness level is attained.
7. Once desired firmness is reached, ensure the switch is returned
to the off position “O”.
USB ChArgINg POrT
1. Your AeroBed
®
product includes a USB port built into the
pump for charging your personal device. Please adhere to the
following guidelines to ensure proper usage.
2. In order to charge your personal device
using the included USB port, the pump must
remain plugged into any standard polarized
120VoltAC electrical outlet throughout the
entire charging cycle.
3. For your convenience, directly below the
pump is a black mesh pocket that may be
used for storing your personal device throughout the charging cycle.
4. Once your device is fully charged, please disconnect the charging cable from the device
and from the USB port.
DEFLATION AND STOrAgE
1. To deflate your bed, open the Quick Release Valve and allow air to expel.
2. For the most compact storage, close the valve and use the Control Wand to press the
DOWN arrow on the switch into the “DEFLATE” position. After all the air is expelled from
the bed, return switch to the off position “O”.
3. Roll or fold the AC cord and wand cord and secure it. Fold the sides of the bed into the
center along its length. Tightly roll and place the bed in the convenient carry bag or other
storage solution and store in a dry, clean location.
4. Store your bed in a clean, dry place at room temperature (above 50 °F/10 °C). Storing your
bed under 50 °F (10 °C) and over 100 °F (38 °C) may affect its performance and will not
be covered under warranty.
SErVICINg OF DOUBLE-INSULATED PrODUCTS
In a double-insulated product, two systems of insulation are provided instead of grounding.
No grounding means is provided on a double-insulated product, nor is a means for grounding
to be added to the product. Servicing a double-insulated product requires extreme care and
knowledge of the system, and is to be done only by qualified service personnel. Replacement
parts for a double-insulated product must be identical to the parts they replace.
INSTRUCTION MANUAL
R111USB
Thank you for joining the AeroBed
®
family by purchasing one of our products. You can expect top-notch quality, innovation and imagination from every AeroBed
®
product. You are about to enjoy
the comfort of an AeroBed
®
product. It is your responsibility to read and always follow the safety, care and maintenance instructions for your new AeroBed
®
product. Always instruct and supervise
others on your bed’s proper use, maintenance and safety.
IMPOrTANT SAFETY
INFOrMATION AND WArNINgS
SAVE ThESE INSTrUCTIONS
rEAD AND FOLLOW ALL INSTrUCTIONS
BEFOrE USINg ThIS PrODUCT.
Preparation of your AeroBed
®
product requires no tools. Use of tools may damage your bed.
When using an electrical furnishing, basic precautions should always be followed, including
the following: Read all instructions before using (this furnishing).
IMPORTANT
• Product is for indoor use only. Do not use outdoors. For Household/Residential Use Only.
• This product has not been evaluated for flammability or cigarette ignition resistance.
WARNING
• Use on flat surfaces only. Bed may tip over on uneven surfaces.
• Remove all sharp objects from area where bed will be set up and used. Do not use this
bed on abrasive surfaces or near pointed/sharp items or surfaces. Bed may puncture.
• Unplug product when not in use.
• Pump is not intended for continuous use. Pump may stop working or overheat if it is
used for extended periods of time.
• Do not use pump continuously for more than 10 minutes.
• To avoid excessive heat build-up in pump, allow pump to cool off for 30 minutes after
each 10 minutes of continuous use.
• Do not attempt to disassemble, repair, or service the pump. No serviceable parts are
contained inside. Contact The Coleman Company, Inc. at 3600 North Hydraulic, Wichita,
KS 67219, 1-800-835-3278 or TDD 1-316-832-8707 in the United States or Sunbeam
Corporation (Canada) Limited, DBA Jarden Consumer Solutions at 20B Hereford Street,
Brampton ON L6Y 0M1, 1-800-387-6161 in Canada for repair and service
center information.
WARNING
This is an electrical product - not a toy. To avoid risk of fire, burns, injury, or shock:
• Always unplug this furnishing from the electrical outlet before cleaning or servicing.
• Use this product only for its intended use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
• Never operate this product if it has a damaged cord or plug, if it is not working
properly, if it has been dropped or damaged, or dropped into water.
• Keep the cord away from heated surfaces.
• Never operate the product with the air openings blocked. Keep the air openings free of
lint, hair, and the like.
• Never drop or insert any object into any opening.
• Do not operate where aerosol (spray) products are being used or where oxygen is
being administered.
• Do not run cord under carpeting. Do not cover with throw rugs, runners or similar
coverings. Arrange cord away from traffic area and where it will not be tripped over.
WARNING
This is the closed position.
Open Air Release Valve.
Close Valve Using 2 Thumbs.
INFLATE
DEFLATE
ADJUST
