INFLATION & ADJUSTMENTS
For better protection of this product never fold, unfold or inflate the airbed in temperatures
below freezing, avoid extensive exposure to the sun and protect from contact with sharp
objects and rough ground.
1. Place your rolled-up bed on the floor or other surface free of obstructions or sharp objects.
2. Make certain the Quick Air Release Valve is closed. If the release valve is open, close it by
using 2 thumbs to push cover and snap into valve. Be careful to avoid pushing valve cover
to the right or left as it snaps into the valve opening.
3. Remove the AC plug and cord from the plastic bag and shrink wrap.
4. Before plugging the pump into the outlet, please confirm that the knob is in the “OFF” position.
5. Plug into any standard polarized 120 Volt AC electrical outlet. North American Electrical
rating: 120 VAC 60 Hz 1.7 A.
(Note: 230 VAC product sold outside of North America).
This product has a polarized attachment plug (one blade
is wider than the other) as a safety feature. This plug will
fit into a polarized outlet only one way. If the plug does not
fit fully in the outlet, reverse the plug. If it still does not fit,
contact a qualified electrician. Never use with an extension
cord unless the plug can be fully inserted. Do not attempt
to defeat this safety feature.
6. Select the desired firmness by rotating the knob on the pump to SOFT, MEDIUM, or FIRM.
The light next to the chosen setting will be illuminated to confirm successful selection.
The pump will inflate the mattress to the selected firmness setting and then shut off
automatically.
7. Once the desired firmness is reached, the pump will monitor mattress pressure and
quietly add air if the firmness drops below the selected setting. The mattress firmness is
maintained when the Comfort Lock light is illuminated. The product must remain plugged
into the electrical outlet for this feature to remain active throughout the night.
8. To change the firmness of your mattress, simply rotate the knob to the new desired
setting. The pump will immediately adjust the firmness to the new setting and maintain
that selected firmness throughout the night.
9. This product is designed to be used overnight to maintain the mattress at the selected
firmness setting. It is not designed to be in operation for extended periods of time. When
the bed is not in use, please turn the knob to the OFF setting and unplug the power cord
from the electrical outlet. This is a temporary bedding solution and is not intended for
everyday use.
USB CHARGING PORT
1. Your AeroBed
®
product includes a USB port built into the pump for charging your personal
device. Please adhere to the following guidelines to ensure proper usage.
2. In order to charge your personal device using the included USB port, the pump must
remain plugged into the electrical outlet.
3. Ensure that your charging cable is securely connected to the USB port on the pump and
also to the charging port of the mobile device.
4. Once your device is fully charged, please disconnect the charging cable from the USB port.
AUTOMATIC DEFLATION AND STORAGE
1. To deflate the mattress, simply rotate the knob to the DEFLATE position. The pump will immediately
begin to expel air and will automatically stop when the mattress is completely deflated.
2. For faster deflation, open the Quick Release Valve and allow air to expel. Then, for more
compact storage, close the valve and place the knob into the DEFLATE position. The pump
will expel the remaining air and will shut off automatically when the mattress is deflated.
3. Fold the sides of the bed into the center along its length. Open Quick Release Valve and
tightly roll the bed, pushing any remaining air out, close Quick Release Valve and place the
bed in the convenient carry bag for easy transport and storage.
4. Store your bed in a clean, dry place at room temperature (above 50 °F/10 °C). Storing your
bed under 50 °F (10 °C)
and over 100 °F (38 °C)
may affect its performance
and will not be covered
under warranty.
INSTRUCTION MANUAL
CL1000/RDV
Thank you for joining the AeroBed
®
family by purchasing one of our products. You can expect top-notch quality, innovation and imagination from every AeroBed
®
product. You are about to enjoy
the comfort of an AeroBed
®
product. It is your responsibility to read and always follow the safety, care and maintenance instructions for your new AeroBed
®
product. This is a temporary bedding
solution and not intended for everyday use. Always instruct and supervise others on your bed’s proper use, maintenance and safety.
IMPORTANT SAFETY
INSTRUCTIONS AND WARNINGS
SAVE THESE INSTRUCTIONS
READ AND FOLLOW ALL INSTRUCTIONS
BEFORE USING THIS PRODUCT.
When using an electrical furnishing, basic precautions should always be followed.
Read all of the following instructions before using this furnishing.
To reduce the risk of electric shock always unplug this furnishing from the electrical outlet
before cleaning.
When using an electrical furnishing, basic precautions should always be followed, including
the following: Read all instructions before using (this furnishing).
DANGER
• Product is for indoor use only. Do not use outdoors. For Household/Residential Use Only.
• This product has not been evaluated for flammability or cigarette ignition resistance.
WARNING
• Use on flat surfaces only. Bed may tip over on uneven surfaces.
• Remove all sharp objects from area where bed will be set up and used. Do not use this
bed on abrasive surfaces or near pointed/sharp items or surfaces. Bed may puncture.
• Unplug product when not in use.
• Pump is not intended for extended periods of use longer than 8 hours. Pump may stop
working or overheat if it is used for extended periods of time.
• Do not attempt to disassemble, repair, or service the pump. No serviceable parts are contained
inside. Contact The Coleman Company, Inc. at 3600 North Hydraulic, Wichita, KS 67219,
1-800-835-3278 or TDD 1-316-832-8707 in the United States or Sunbeam Corporation
(Canada) Limited, DBA Jarden Consumer Solutions at 20B Hereford Street, Brampton ON L6Y
0M1, 1-800-387-6161 in Canada for repair and service center information.
WARNING
To reduce the risk of burns, fire, electric shock, or injury to persons:
• Unplug pump before putting on or taking off parts.
• Close supervision is necessary when this furnishing is used near children or disabled persons.
• Use this furnishing only for its intended use as described in these instructions. Do not
use attachments not recommended by the manufacturer.
• Never operate this furnishing if the plug or card has been damaged, if it is not working
properly, if it has been dropped or damaged, or dropped into water. Contact the
manufacturer for assistance in these matters.
• Keep the cord away from heated surfaces.
• Never operate the furnishing with the air openings blocked. Keep the air openings free
of lint, hair, and the like.
• Never drop or insert any object into any opening.
• Do not use outdoors.
• Do not operate where aerosol spray products are being used or where oxygen is administered.
• To disconnect, place the knob in the OFF position, then remove plug from outlet.
• Warning - Risk of injury to Persons - do not use this furnishing to support video
equipment such as televisions or computer monitors.
• This pump includes a mechanism to protect against high temperatures. When the
primary pump runs for an extended period of time, it will automatically shut off to
avoid overheating. Allow the pump 30 minutes to cool down before next use.
• Maximum loads are as follows: Queen (600lbs - 272Kg), Full (600lbs - 272Kg), Twin
(300lbs - 136Kg).
SAVE THESE INSTRUCTIONS
WARNING
This is the closed position.
Open Air Release Valve.
Close Valve using 2 thumbs.
SERVICING OF DOUBLE-INSULATED PRODUCTS
In a double-insulated product, two systems of insulation are provided instead of grounding.
No grounding means is provided on a double-insulated product, nor is a means for grounding
to be added to the product. Servicing a double-insulated product requires extreme care and
knowledge of the system, and is to be done only by qualified service personnel. Replacement
parts for a double-insulated product must be identical to the parts they replace.
