SN
10
p
lu
s
lo
n
g
si
d
e
About This Document
www.aerocompact.com
6
Tools
Certain tools are required to carry out the assembly. These tools are shown in the illustrations with the fol-
lowing symbols.
Measuring tape, measure
Cordless screwdriver, screwdriver
Pencil, mark
Torque wrench,
Observe torque
Chalk line
Target group
These installation instructions are intended for trained personnel who are familiar with the installation of
photovoltaic systems. The personnel should also be familiar with working on roofs and know the local reg-
ulations regarding work safety. The personnel must also observe the instructions in the Safety chapter.
Appropriate use
The CompactFLAT flat roof system is designed exclusively for installing PV modules on flat roofs or similar
flat surfaces. Proper use also includes correct installation in accordance with these installation instructions.
PV modules used with the CompactFLAT system should be approved by the module manufacturer.
AEROCOMPACT accepts no liability for loss of performance or damage of any kind to the PV modules.
Any other use of the CompactFLAT system is considered improper.
Liability, Warranty, Guarantee
These assembly instructions and the project report supplied with the product are integral parts of the
product. The information, data and instructions given in the assembly instructions were up to date at the
time of printing. No claims can be made for products already delivered that deviate from the information,
illustrations and descriptions.
The project report supplied with the system contains the static calculation related to the location. Follow
the position of the modules on the roof, the number and position of the building protection pads and the
ballast distribution exactly according to the project report. If the module layout on the roof changes due to
local conditions, e.g. unforeseen interference areas, the structural analysis must be recalculated. The Aero-
compact system is designed and planned using the AEROTOOL software.
Aerocompact accepts no liability for damage and malfunctions caused by:
o
Improper use
o
use of non-certified components.
o
unauthorized modifications to the product.
o
improper handling of the product.
o
Installation errors
o
Failure to comply with the installation instructions or planning documents.
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
