background image

 

33 

Check the torque of every bolt 
Tighten head nuts (in cross order) with a Torque Wrench at 2.2 Kg.m (22Nm)  

Check the tension and condition of the reduction belt 

Check fuel lines 

Check the wiring 
Check that the cord of the starter has no abrasions 

Grease the link-sphere between the manifold and the exhaust pipe with lubricating copper-grease 

suitable for high temperature (up to 1100°). If you can’t find it on the market, please ask your dealer. 
 

Every 50 hours: 

Same controls of the 20 hours and furthermore: 

Check the torque of the engine’s crankcase nuts 
Change spark plugs 

Change the petals of the reed valve 

Check the reduction belt and the play of the pulley and change them in case of need 
Check the conditions of the starter gears (version with electric start) 

Once a year (independently from flight hours) change the diaphragm of the carburetor. 

 
Refer to the CORS-AIR M 25 Y Manual for more information. 

 

12.8 Thor 250 Engine Maintenance 

 
Before each flight: 

Check the exhaust system condition 

Check the electric wiring condition 
Check fuel line condition 

Check the bolts and screws tightening 

Check the silent-block conditions 
 

After the first 10 hours: 

Replace the gear oil  

Check the carburetion 
 

Every 50 hours: 

Replace spark plug (use Champion RN2C plugs) 
Clean the air filter  

Replace the gear oil 

Check the starter wearing  

 
Every year or every 100 hours: 

Replace the air filter  

Clean the carburetor  
Replace the silent-block  

Replace the fuel system pipes 

 

Every 100 hours: 
Replace muffler springs  

Check the reed valve  

Check the piston, the piston rings and the small end bearing  
Decarbonize and clean the decompression hole 

 

Every 150 hours: 
Remove the gear and check the clutch and bell wear  

Replace the piston, the piston rings and the small end bearing  

replace the silencer deadening material  

Replace the reed valve 
Every 300 hours: 

Replace all the bearings and seals  

Replace the crankshaft  
Replace the cylinder 

Summary of Contents for ANT



































Reviews: