background image

4/28/2021

Nano Shutter User Guide : Aeotec Help Desk

https://aeotec.freshdesk.com/support/solutions/articles/6000198854-nano-shutter-user-guide-

1/15

Nano Shutter user guide.

Modified on: Mon, 1 Jun, 2020 at 7:04 PM

Aeotec Nano Shutter.

Aeotec Nano Shutter

 (https://aeotec.com/z-wave-motor-shutter-curtain-control)

 has been crafted to power connected

sockets and switches using 

Z-Wave Plus

 (http://aeotec.com/z-wave-plus)

. It is powered by Aeotec’s 

Gen5

(http://aeotec.com/z-wave-gen5)

 technology. 

To see whether Nano Shutter is known to be compatible with your Z-Wave system or not, please reference our 

Z-Wave

gateway comparison

 (http://aeotec.com/z-wave-gateways)

 listing. The 

technical specifications of Nano Shutter

(https://aeotec.freshdesk.com/solution/articles/6000198818-nano-shutter-technical-specifications-)

 can be viewed at that link.

Familiarize yourself with your Nano Shutter.

Important safety information.

Please read this and other device guides carefully. Failure to follow the recommendations set forth by Aeotec Limited may
be dangerous or cause a violation of the law. The manufacturer, importer, distributor, and/or reseller will not be held
responsible for any loss or damage resulting from not following any instructions in this guide or in other materials.
 

Summary of Contents for Nano Shutter
















Reviews: