Aeroworks 60cc Freestyle Extra 260 Assembly Manual
71
Fuselage with Fin
– covered, firewall fuel-proofed:
(4) 8-32 blind nuts pre-installed for main landing gear
mounting
(14) 4-40 blind nuts pre-installed (8) for cowl mount-
ing (4) for Stab mounting (2) for Long Pipe Mounts
(1) Canopy – Painted and pre-installed with (2) 4-40
Blind nuts and (2) 4-40x25mm Button Head bolts
and (2) #6 Bonder Washers
(1) Receiver Floor pre-installed with (4) T2.6x10mm
Screws
(1) Engine Box Top Hatch Cover pre-installed with (4)
T2.6x10mm Screws
(1) Long Pipe Front Hatch Cover pre-installed with (4)
T2.6x10mm Screws
(1) 3.5(o.d.) Antenna exit tube installed
(2) 3.5(o.d.) x 60mm pull-pull exit tube installed
Left Wing with Aileron
– covered: Pre-Slotted for the
mounting of the control horns
(7) Big Pin Point hinges in place –
Not Glued
(2) 10mm dia. anti-rotation pins installed
(1) 8-32 blind nut pre-installed for wing mounting
(2) 6-32 blind nuts pre-installed for outside SFG
mounting
(1) Aileron Servo Sting pre-installed pulled out of
the 8mm rubber Grommets
(1) Pre Installed Slot for the Inner SFG with
Covering Not Removed
Right Wing with Aileron
– covered: Pre-Slotted for the
mounting of the control horns
(7) Big Pin Point hinges in place –
Not Glued
(2) 10mm dia. anti-rotation pins installed
(1) 8-32 blind nut pre-installed for wing mounting
(2) 6-32 blind nuts pre-installed for outside SFG
mounting
(1) Aileron Servo Sting pre-installed
pulled out of
the 8mm rubber Grommets
(1) Pre Installed Slot for the Inner SFG with
Covering Not Removed
Horizontal Stabilizer
with elevator assembly with (5)
big pin point hinges –
Not Glued
---covered
Elevators Pre-Slotted for the mounting of the control
horns
Rudder
with (6) big pin point hinges -
Not Glued
–
covered
SUB ASSEMBLIES:
#1:
(1) Fiberglass Cowl – painted with pre-drilled mount-
ing holes
(8) 4-40x14mm Button Head Bolts for cowl mounting
(8) #6 Bonded Washers
(8) 3mm Split Ring Lock washers
#2:
(1) 5mm Aluminum Main Landing Gear
(4) 8-32x25mm hex head Bolts – main landing gear
mounting
(4) 4mm flat washers for main landing gear mounting
(4) 4mm split ring lock washers for main landing gear
mounting
(2) 5x45mm AL Axle bolts
(4) 5mm Flat Washers – Wheel Spacer
(2) M8 Lock Nuts
(4) 5mm i.d. Wheel Collars with set-screws
(4) 4-40x14mm Button Head bolts for wheel pants
mounting
(4) 3mm flat washer for mounting wheel pants
(4) 3mm split ring lock washer for mounting wheel
pants
#3:
(2) 3.5” (85mm) Dia. Main Wheels (Lite Type)
#4:
(2) Wheel Pants—1 Left and 1 Right---Painted
(4) 4-40 blind nuts installed on the wheel pants, 2
per side.
#5:
(1) Aluminum Tail Wheel Assembly – Medium
#6
(10) Fiber plate Horns Single Output– Laser Cut –
Aileron (4); Elevator (4); Rudder (2)
(6) ABS Black Horns back plate
(2) 4-40x3” Left hand and Right hand threaded push-
rods with nuts for ailerons
(2) 4-40x2.5” Left hand and Right hand threaded
pushrods with nuts for elevators
(1) Wrench for the left hand and right hand threaded
pushrod
(4) Brass spacers – 2 for ailerons; 2 for elevators;
(8) 4-40 Ball Link – 4 for ailerons; 4 for elevators;
(8) 4-40x16mm hex bolts
(8) 4-40 lock nuts
(4) 3mm flat washers
#7
(2) 1x1100mm plastic coated pull-pull steel cable
(4) 4-40 Threaded Coupler with nuts
(4) 3.5x5mm brass pull-pull swaging tubes
(4) 4-40 Ball Links for rudder servo
(4) 4-40x16mm hex head bolts
(4) 4-40 Lock nuts
(2) Brass Spacers
(4) 3 flat washers
#8
(1) 32x830mm Carbon/Fiber Compound Wing Tube
(2) 12.5mm Carbon/Fiber Compound Stab Tubes -
(Front 175mm - Rear 382mm)
(2) 8-32x25mm Hex Head Wing Mounting Bolts
(2) #8 Bonded Washers for wing mounting
(2) 4mm split ring lock washers for wing mounting
(4) 4-40x16mm Button head bolts for stab mounting
(4) #6 bonded washer for stab mounting
(4) 3mm split ring lock washers for stab mounting
(4) 1.8mm cotter pins
60cc FREESTYLE EXTRA 260
MATERIALS LIST