6
Right Top Wing with Aileron
– covered:
(2) 8-32 blind nuts installed for the Outer struts
mounting.
(2) 2mm steel L bracket – outer struts fitting prein
stalled at the root of the wing
(8) pin point hinges glued
(1) Aileron servo string installed
(1) Pilot holes pre drilled for control horn mounting
Left Bottom Wing with Aileron
–covered:
(2) 8-32 blind nuts installed for the Outer strut
mounting.
(8) pin point hinges glued
(1) Locater pin glued
(1) Aileron servo string installed
(1) Pilot holes pre drilled for control horns mounting
(2) Pre drilled holes for the wing retainer bolts
Right Bottom Wing with Aileron
–covered:
(2) 8-32 blind nuts installed for the Outer strut
mounting.
(8) pin point hinges glued
(1) Locater pin glued
(1) Aileron servo string installed
(1) Pilot holes pre drilled for control horns mounting
(2) Pre drilled holes for the wing retainer bolts
Horizontal Stabilizer with elevator assembly
with (12)
pin point hinges (glued)---covered
(2) Pilot holes pre drilled for control horns mounting
Rudder with (9) pin point hinges
(not glued) – covered
(2) Pilot holes pre drilled for control horns mounting
SUB ASSEMBLIES:
#1:
(1) Fiberglass Cowling, - painted
(2) 6-32 blind nuts – pre installed for the top cowling
Mounting
(2) 4-40x16mm hex style head bolts for the bottom
cowling mounting
(2) 6-32 hex head bolts for top cowling mounting
(4) #6 bonded washers
(2) 3mm split ring lock washers
(2) 3.5mm split ring lock washers
#2:
If center cabane fairing will be used
(1) Plastic vacuumed fairing for center cabane
(2) 8-32x40mm for fairing mounting
(4) 9mm (long) Metal Spacers
(4) #8 Bonded Washers
(2) 8-32 Lock Nuts
OR:
If No center cabane fairing will be used
(2) 8-32x15mm bolt
(2) 8-32 Lock Nuts
#3:
(2) Aluminum Main Landing Gear, 1 left and 1 right,
painted
(2) 5mm dia. x 48mm AL Axle
(2) M8 lock nuts
(4) 5mm Wheel Collars with set-screws
(2) 8mm flat washers
(2) 4” Dia. Main Wheels
(4) 4-40x14mm hex style bolts for mounting wheel
pants
(4) 3mm flat washer for mounting wheel pants
(4) 3mm split ring lock washer for mounting wheel
pants
(8) 8-32x25mm hex head bolts for mounting main
landing gear
(8) 4mm flat washers for mounting main landing gear
(8) 4mm split ring lock washer for mounting main
landing gear
#4:
(2) Wheel Pants—1 Left and 1 Right---Painted
(4) 4-40 blind nuts installed in the wheel pants
#5:
(1) Aluminum Tail Wheel Assembly - Large
#6:
(2) Outer struts – Left and Right, covered, marked with
BL, BR
(8) 8-32x10mm hex head bolts for the Outer strut
mounting
(8) 8-32 lock nuts for the Outer strut mounting
(8) 2mm L steel Outer strut fittings
(8) 8-32x15mm hex head bolts for the steel L bracket
for Outer strut mounting
#7:
(6) 4-40 3” left hand and right hand threaded pushrod
with nuts and carbon tubes for elevators and ailerons
(1) Wrench for the left hand and right hand threaded
pushrod
(2) 4-40 x 300mm Threaded pushrod
(2) 4-40 solder couplers
(8) Brass spacers – 4 for ailerons; 2 for elevators; 1 for
throttle; 1 for choke
(10) 3mm flat washers – 4 for ailerons; 2 for elevators; 2
for throttle; 2 for choke
(16) 4-40 Ball Link – 8 for ailerons; 4 for elevators; 2
for throttle; 2 for choke
(16) 4-40x16mm hex style bolts
(16) 4-40 lock nuts
#8:
(2) 1.0x1100mm plastic coated pull-pull steel cable.
(4) 4-40 Metal R/C links with nuts
(4) 3.5x5mm brass pull-pull swaging tubes
(8) AL double control horns
(48) T2.6x16mm Phillips head mounting screws for the
control horns
