Afag 50030771 Translation Of The Original Montage Instructions Download

Page: 3 / 28

UG 20-UG 25-OI-vers. 3.2 gb. 06.08.14.doc

Table of Contents:

1.0.0

Declaration of Incorporation

Page 4

1.1.0 Declaration of Incorporation according to the Machinery Directive 2006/42/EG

2.0.0

Module Information

Page 5

2.1.0 Transport and storage (packing and unpacking)

Page 5

2.1.1 Assembly for the gripper

Page 6

2.1.2 Mounting for the gripper fingers

Page 6

2.1.3 Hole matrix and centering bushings

Page 7

2.1.4 Tightening torques for bolts

Page 8

3.0.0 Montage Instructions

Page 9

3.1.0 Manufacturer address

Page 9

3.1.1 Symbols

Page 10

3.1.2 General description

Page 10

3.1.3 General description for the module

Page 11

3.1.4 Scope of supply

Page 12

3.1.5 Intended use

Page 12

3.1.6 Guarantee

Page 13

3.1.7 Areas of application

Page 13

3.1.8 Dimensions drawing UG 20

Page 14

3.1.9 Technical data of the UG 20

Page 15

3.2.0 Preferred combinations UG 20

Page 16

3.2.1 Dimensions drawing UG 25

Page 17

3.2.2 Technical data of the UG 25

Page 18

3.2.3 Preferred combinations UG 25

Page 19

3.2.4 Pneumatic connection UG

Page 20

3.2.5 Preparation for commissioning

Page 21

3.2.6 Preparation for Start-up

Page 21

3.2.7 Fitting the proximity switch in the module groove

Page 22

3.2.8 Example of application of sensor technology combined with

Page 23

4.0.0 Maintenance Instruction

Page 24

4.1.0 Maintenance and servicing of the UG 20 / UG 25

Page 24

4.1.1 Servicing

Page 25

4.1.2 Accessories for the UG 20 / UG 25

Page 26

4.1.3 Trouble-shooting

Page 26

4.1.4 Disassembly and repair

Page 27

5.0.0 Disposal

Page

Summary of Contents for 50030771





























Search results

Summary of Contents for 50030771

Reviews:

Related manuals for 50030771

Brands by name

Popular brands

Afag 50030771, Translation Of The Original Montage Instructions

Search results

Summary of Contents for 50030771

Reviews:

Related manuals for 50030771

Brands by name

Popular brands