aFe Power 51-22642-B Instruction Manual Download | Manualshive

Page: 12 / 16

background image

Page 12

5

Step 17: Reconnect the vent fitting. It will snap over without having to release the plastic clip. Pull up
slightly to confirm installation.
Step 18: Installation is complete. Any codes can be cleared with a code reader or by disconnecting the
battery. You will lose any radio presets with battery disconnection.

NOTE: If removal of the vent insert is required, it can be pulled out with internal snap ring pliers.

Refer to Figure I for Steps 17-18.

( For V6-3.5L (tt) only, not necessary on V6-2.7L (tt) )

Figure I

INSTALL

«
...
10
11
12
13
14
...
»

Summary of Contents for 51-22642-B

















Reviews:

No comments

Related manuals for 51-22642-B

Brand: O.S. engine Pages: 21

Brand: O.S. engine Pages: 25

Brand: Subaru Pages: 52

Brand: Vascat Pages: 60

Brand: Eaton Pages: 16

Brand: Scania Pages: 78

Brand: Stobag Pages: 12

Brand: Leroy-Somer Pages: 8

Brand: Leroy-Somer Pages: 6

MICRO GEARLESS XAP1-CE

Brand: Leroy-Somer Pages: 12

240Z S30 series

Brand: Datsun Pages: 41

Brand: Metronic Pages: 24

Brand: Honda Pages: 31

Brand: TTBIO Pages: 2

Brand: New Holland Pages: 150

Brand: Tecno Automazione Pages: 2

Brand: A-iPower Pages: 52

Brand: rojaflex Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands