aFe Power 51-22642-B Instruction Manual Download | Manualshive

Page: 4 / 16

background image

Refer to Figure A for Steps 1-4.

Step 1: Disconnect the Temperature sensor plug from stock tube. 1
Step 2: Loosen the OE intake clamps using an 8mm nut driver from the left and right side runners. 2
Step 3: Unclamp the top portion of the OE airbox. 3
Step 4: Remove the OE intake and the top portion of the OE airbox by pulling straight up and out of the
vehicle.

REMOVAL

Page 4

Figure A

2

2

3

1

«
...
2
3
4
5
6
...
»

Summary of Contents for 51-22642-B

















Reviews:

No comments

Related manuals for 51-22642-B

Brand: VEM Pages: 35

Brand: Baratza Pages: 5

Brand: GPX Pages: 43

Brand: Mercury/Mariner Pages: 130

Brand: Mercury Pages: 18

Brand: Mercury Pages: 9

Brand: Mercury Pages: 85

Brand: MerCruiser Pages: 895

Brand: Bauer Pages: 52

Brand: Stiga Pages: 168

Brand: CHEE SIANG INDUSTRIAL Pages: 57

Brand: LinMot Pages: 48

Brand: Desert Aircraft Pages: 8

Power 60 Brushless Outrunner

Brand: E-FLITE Pages: 4

Brand: Mitsubishi Pages: 16

Brand: Mitsubishi Pages: 120

Brand: Zenoah Pages: 4

Brand: YOODA Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands