USING YOUR SENTRY SYSTEM™ CONTROL
6
SET
SET
SET
ON OFF Door Ajar
Power Failure
Hi / Low Temp Upper
Hi / Low Temp Lower
Initial Power-Up:
Your product will immediately start upon plug-in to power
receptacle. The Sentry System LED will be flashing “amber” on
single-zone models, (Figure 6), or displaying “power failure” on
dual-zone models, , (Figure 7), to indicate that a power outage
has occurred. This is normal as the product was powered-up at
the factory for quality assurance testing. Momentarily press and
release the “ON/OFF” keypad to reset the control alarm status.
LED should indicate steady green.
Set Display Temperature Units:
Your control is factory set to display temperature in
º
Celsius as
indicated by
º
C in the upper right corner of the temperature
display. If this is the desired temperature units, no action is
required. If you prefer to display temperature in
º
Fahrenheit,
momentarily press the “
º
F/
º
C” keypad.
º
F should now be dis
-
played in the upper right corner of the temperature display. You
may “toggle” between
º
F or
º
C temperature display at any time
by momentarily pressing the “
º
F/
º
C” keypad.
Set Your Desired Storage Compartment Temperature:
Your control is factory set to 13
º
C. This is the ideal long-term
storage temperature for “both” red and white wines. The stor
-
age compartment temperature can be adjusted throughout the
full range of red and white wine serving temperatures, (4
º
C to
18
º
C).
Single-Zone Models, (Figure 6)
To set the storage compartment temperature, momentarily
press the “Set” keypad. The display will now change to show the
current set-point temperature, and “SET” will be displayed to in
-
dicate that you are in temperature set mode. While in SET mode
you may press the “Warmer” or “Colder” keypads to adjust the
set-point to your desired temperature in 1
º
increments. When
your desired temperature is displayed, you may exit SET mode by
momentarily pressing the “Set” keypad, or SET mode will time-
out after 10-seconds of inactivity.
Dual-Zone Models, (Figure 7)
The control allows independent temperature control for both
the upper and lower storage compartments. On Dual Zone
models, momentarily pressing the “Set” keypad will select each
compartment individually as indicated by SET being displayed
in the “Upper” or “Lower” compartment temperature display.
While SET is displayed, you may press the “Warmer” or “Colder”
keypads to adjust the storage compartment set-point to your
desired temperature. To exit SET mode, momentarily press the
“Set” keypad until SET is no longer displayed in either the Upper
or Lower displays, or SET mode will time-out after 10-seconds of
inactivity.
Compartment temperatures will be controlled to the tempera
-
ture displayed when SET mode is exited.
Important: it is suggested to allow 24-hours after changing the
storage compartment set-point temperatures before making
further adjustments. This will allow the content temperatures to
stabilize at the new set-point temperature. Frequent door open
-
ings may prolong this stabilization period.
Interior Lighting:
A door activated interior compartment light is provided for your
convenience. On glass door models only, this light may also be
used to enhance the display of your wines through the glass
door. To activate the display lighting mode on glass door models,
momentarily press the “Light” keypad, (Figure 6 and 7). When
activated, the interior light will remain on when the door is
closed.
Important: Use the display lighting option only when needed.
The interior light generates heat which will increase the energy
consumption of your product.
Figure 6 “Single Zone”
Glass and Solid Door Models
Figure 7 “Dual Zone”
Glass Door Models
Status LED
Status
message
ON
OFF
Press and hold
Set
Warmer
Colder
F/C
Light
Sentry System™
Power Failure-Flashing Amber
High/Low Temp-Red
Press ON/OFF-Reset
Alarms OFF-Steady Amber
